I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Im implementing an application which uses the s132 SD for BLE communication and the mesh implementation described at nRF51-ble-bcast-mesh. I need to have encrypted and authenticated...
Hi Forum,
I'm using SDK12 without ble. (peripherals/uart)
so, I can't pstorage or fstorage.
I want to write 4 bytes without erasing a page. And I want to update a value...
Hi. I'm using nRF52832, SDK13.0.0, S132.
When I make bootloader, I should make *.setting file for application.
Do i need *.setting file when I update just application...
Hi,
this is not a question about the nRF but about Android programming. Hope some of you can help me anyways. I modified the android part of the nRF Blinky example github...
Hi Nordic Team,
I saw some issue with Nrf connect on IOS.
First the App crash when i open it.
Second with IOS i can see some issue with pairing and bonding...
Hello,
I intended to implement an application without OS. Due to safety concerns I would like to have two call stacks : one for softdevice using MSP and the other for my...
After programming the Ble_app_uart to the nrf52832, I am sending a 100 Bytes of data from my UART Port to Nordic chip and this data is transferred over BLE to my Phone. I...
According to Table 19 in the nRF24L01+ datasheet, writing to any of the 32 command registers is "Executable in power down or standby modes only". This caveat is also repeated...
Basically I want to get a 8 byte long MIC when using the AES CCM encryption. From the product specification it does seem like I can only get a 4 byte MIC, is that correct...
Hello,
I try to flash my dev card nrf52 with the program ble_app_uart
Or a program ble by cons I can flasher by other program (pin change in), I do not know from where the...
I created an characteristic that has MAX_Length = 20 Bytes characteristic.
And When I'm trying to write less than 20bytes on this Characteristic, It Always send with 20Bytes...
Is it OK to send multiple packet continuously over nus at below way without waiting for packet transmit complete?
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{...
Hi,
I'm using nrf51822 Ek kit and running ble_app_uart example,when i want to send any character or integer it Received like a string only,but i want to send only single...
Hi,
this question is more about iOS than nRF, but there's probably here some experience around this subject.
First the context : We have a product based on nRF51, S110...
