Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hi, it's probably a very dumb question, but i don't seem to find any details about it. In nrf52 SDK documentation, in Error Module section it says
The behavior of the...
Hi friends...!
I want to put dynamically changing MPU data into the advertising packet. I am putting my accelerometer data into manufacturer specific data field of ble_advdata_t...
How robust is the output PA of the nrf905?
Assume the ouput matching network and 50Ohm connector is used as in the 868Mhz application note.
If the antenna is removed...
Hi,
I'm trying to find a way to speedup the upload procedure of an application, via BLE on a Arduino Primo with the DFU service.
Here you can find my code:
https://github...
Hi,
I am using ble_app_uart sample code for testing. In that I want to store the incoming data into to three buffers and simultaneously sending this over BLE. i.e., consider...
hi i m using nrf52832 for detection acceleration , angular speed and detection of magetic field with GY-87 ( MPU 6050 and Hmc5883). in fact i wrote a program that read only...
Hi,
I am using s130v2 and running the example code from: nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_hrs\pca10028\s130\arm4
This is the only modification I...
Hi,
I know this is a Bluetooth 5 spec question, but wanted to know the practical figures for current consumption when nrf52840 is used as both central and peripheral...
Hi,
We are expecting many of our devices to be in close proximity. How can we be certain that when a user initiates a buttonless DFU, that they are uploading to the correct...
Hi,
I thought central is the one which fills up its look up table with 16 bit IDs to keep track of the peripherals. If multiple devices can act as central at the same time...
I am trying to re-base my SDK package, and when I started off with the ble_app_template project for the pca10040 s132, I copied my main file on top, everything compiles just...
I am developing an application which involves control of a brushed DC motor with a quadrature encoder. According to this post, in SDK 12.2.0 - which I am using - it is possible...
Hi,
I had a problem with my NRF52 chips. I'm using one BL652 (Laird) with SoftDevice s132 (4.0.2) and a standalone nRF52832 also with the same SoftDevice. I was trying...
hi guys. i'm have a project with nrf52832.
i use jlink v8 debuger clone form china, just 12$ and have this troulbe in this figure
Untitled.png
could you help me?. jlink...
