Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
I am trying to use optiboot-ble with the nRF8001 and an atmega328p to allow application update over bluetooth. I have successfully compiled the bootloader and flashed it to...
Data sheets
Where is the data sheet for the
NRF51822 SoC located?
I am also looking for the ARM
Cortex-M0 data sheet, where is
this located?
I need to find...
When I try to program an example with nRF go Studio from the new SDK12 or SDK13(fresh download) I get the following error:
It does not show up if I don't program the...
Hi nordic guys,
I used the ble_app_hids_mouse demo to build my generic hid device(no mouse and keyboard) project.Now i modified the hids_init() function according my hid...
Hi !
I work for about a year with a nRF52832 custom board without problem and recently I add a bootloader (with success) on the firmware.
Now I can't connect through...
My application is based on ble_uart_app. I want to integrate the DTM so that the nRF51 will be in RF test mode when it receive command from UART. However, I found that the...
Hi all,
We're going to implement floating point agorithms on the new chip which has a FPU (cortex M4F). with the 64MHz system clock, how many flops can we have? I could not...
Hello.
I use nRF52 & mpu9250.
I want to use dmp.
But now it's not going well.
Now, there is no error,but fifo_count doesn't change after fifo_count became 512.
I...
Hi,
sometimes not always, the function peer_id_is_allocated return false and this causes an ASSERT of device, because a NRF_ERROR_INVALID_PARAM is returned by pdb_write_buf_get...
Hi,
We're using nRF51822 and in the future we'll use nRF52832.
We do use bluetooth, but as far as I know, we don't use encryption (code is based on the HRS example, and...
Is nrf52 support 3 wire spi interface? I am using AD9837 3-wire spi module act as slave and nrf52 dk act as master. I am using SCLK, SSn(i.e.,Fsync) & MOSI pins only.I want...
Hi, I’m a newbie of nRF SoC. I have a BLE gadget with nRF51822_xxAC that controls LEDs and obtains data from accelerometers through I2C(TWI) devices. The hex file for the...
Hello,
I am able to get NRFtoolbox dfu code work for iOS 10.3. and now able to perform the DFU on BLE device.
But when I perform the DFU its GAP name changes from Beam...
Hi
I migrated from SDK11 to SDK12/13.
In SDK11 I already had avaiable a softdevice to use for ble_app_uart peripheral.
In the new SDK I have to build the softdevice but...
I'm trying to understand example "ble_app_hts" how after advertising make a connection. I didn't see in code any call of function "sd_ble_gap_connect" ? how is made connection...
