Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Using the nina 112 with nrf52832 SDK 13
I have got a problem with the I2S Interface.
I configured the RESET Pin as normal PIN. Tested with GPIO as Output it worked. If im...
Can we build the FW manually and upload to the Thingy via the OTA uploader? We built the FW, created the DFU, and inserted the .zip file in the iOS app, however get an Error...
Hello!
I am working on a project. The goal is to retrieve every seconds some acceleration data from the ADXL362 accelerometer.
I configured the spi in blocking mode...
Am i right in thinking that if GPREGRET has not been set then we can not guarantee what value it will be?
I.e on power up we can not guarantee that its value is 0.
List item
Hi,
i am working on nrf52 sdk11 softdeviceS132,
Working on custom board i have edited ble_app_uart example and implemented my application it is using PWM_Library...
Hi,
I would like to receive data sent from an nRF52840 through Bluetooth in a Java desktop application. The Java app can run on Windows or Linux, I am using Windows 10...
Hi, I am working on ble_alert_notification example provided in sdk 11 using s130. This example is peripheral code in client role. I have tested it using MCP. I wanted to use...
The absolute max throughput for the nRF52 using S132 v2 was 128 kbps .
The new S132 v3 was recently released and boasts throughput increases by 400%. Has anyone tested...
I am trying to send small data packets of up to 9 bytes at the fastest and most consistent rate from a nRF52 peripheral to a nRF52 Central. Both use the s332 SoftDevices....
Hello !
I've created an app based on the nrf blinky master : it works perfectly on my smartphones.
But when I kill the app, and when I relaunch it, it doesn't connect...
Hi,
I am trying to use a mux change among 3 differential channels. The diff signal then goes through an instrumentation amplifier. The steps I'm using:
switch to ch1...
Occasionally, when trying to program a softdevice in nrfgo studio, it can't find the softdevice hex file. It was there during the last several programming sessions, but now...
I would like to achieve in the room inside a number of devices to achieve one-to-one binding 8K / S unidirectional transmission of data, is not the use of proprietary_rf inside...
Hi,
I have set up a two NRF51DKs one in a central and one in a peripheral role. Using MCP and nRFConnect I have confirmed that I can send read requests to my peripheral...