I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
Hi,
I'm trying to configure the SPI by using the nrf_drv_spi. the problem that I'm facing is the configuration of the "spi_config.SPI_CPHA = SPI_CONFIG_CPHA_Leading" which...
Hi!
We are using ble_radio_notification for changing the advertisement data after every advertisement.
The problem is that it doesn't work, the device freezes when trying...
I have designed a custom PCB with Nrf52 for an ECG wearable sensor application and is trying to optimise the power consumption of the device. The application is to collect...
Hi.
I'm currently trying to scan beacons with timeslot example.
However, I found that there're more than 20% of loss while scanning beacons broadcast.
I think that...
Hi, I tried Adding another service to the LBS Program, but the chip is getting reset , i have another 16 bit uuid service with different base uuid, Its getting stuck at SOFTDEVICE_HANDLER_INIT...
hi
im using nrf51422 v2 with external sdk v6 with softdevice v7
im running one of example that its name is ble_app_template and when i run it , it show up for just one phone...
hello,
I want to change the advertise time out time by BLE_GAP_ADV_TIMEOUT_LIMITED_MAX.
Is there a problem with changing BLE_GAP_ADV_TIMEOUT_LIMITED_MAX to ex. 1000sec...
Hi,
I can use nRFgo Studio via nRF5x Bootloader to update application firmware(Hex file).
It look to be using "nrfutil.exe" to create a XXX.zip file and go through UART...
Hi.
I am on nRF52 DK (PCA10040 v0.9.0, s132 SD), SDK 0.9.2 and Linux (Ubuntu).
I am currently working on the SDK's example ble_app_uart.
I am only using gcc, and...
I was working with examples/ble_peripheral/ble_app_gls. In the SDK11alpha configuration, I paired the dev board with my Android phone running nRF Toolbox and was able to start...
Hi,
I loaded S110 v8 to nrf51. Then I loaded dfu_dual_bank_ble_s110_pca10028 bootloader.
With this setup, I'm able to download my application via the bootloader.
The...
Hi,
Reading the nRF52 product specification, I see:
"If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the supply due to...
Req: from the cap-sense board, different tap will be done by user (like 2 times tap, 3 three times tap etc). so the Bluetooth board (nrf52) will receive these taps as interrupt...
Hello Devzone fellows :)
As you may notice, we have posted our first webcast: Interfacing with Nordic's Softdevices .
It's the first test run in a series in which we...