Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi
I'm looking for a functional example based on Freertos and nrf52 on SDK11 and SD132. I'm having problems (hard fault) and I've been looking for this example but with...
Hi There
I see there is a Proximity App - is this available for downloading like the beacon App ? for use in xcode ?
Also, in the demo, there was a bluetooth unit that...
I use a android phone as central(Master) and use a nrf51822 as a peripheral(Slave).
The peripheral can send the "L2CAP Connection Parameter Update Request" to change the...
Hi
I have a BLE nRF51822xxAA project created with Keil 5.15, SD 100 ver 802 and Family Pack 803.
I made a new configuration in a new machine with Keil 5.2 and I am getting...
I want to create my own PCB which can communicate with the following Transmitter:
www.hobbyking.com/.../_ 43854__Turnigy_5X_5Ch_Mini_Transmitter_and_Receiver_Mode_2 .html...
Hi! I work with a smart Beacon Kit nrf51822 rev1.0.0, s110 and I have visualised my current consumption. What I expected to see is that my beacon could send in one time all...
We are preparing a project where several mobile phones
with Android OS in peripheral role will be connected continuously to
one nrf51822 with S130. Communication must be...
On nrf51 I was using:
pre flash: w4 4001e504 1
erase all: w4 4001e504 2\n w4 4001e50c 1\n sleep 100
pin reset: w4 40000544 1
Is it still the same for nrf52...
[Edited title]
My application on a PCA10028 board is attempting to send a BLE advertisement using sd_ble_gap_adv_data_set() by going through ble_advdata_set in ble_advdata...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi,
is there something like a makefile for nrf52 out there?
I want to use eclipse and gcc in osx. It worked great for nrf512 but nrf52 has other addresses and maybe...
Hello all,
Lets assume that central bonded with nRF51822 peripheral and than disconnected. If bond is saved on peripheral- ok, cental send BLE_GAP_EVT_SEC_INFO_REQUEST...
When i try to do an update with Nrfutils Under android i get a REMOTE_DFU_OPERATION_FAILED since i added signing.
I created my pem file key with nrfutil.exe keys
i copied...
Hi
I'm trying to get working a project by using S132 v3 alpha. I'm stuck at function sd_ble_enable. This function should return the minimum RAM memoy would need the SD...
Hi Nordic.
So, I am using GAZELL to link a sensor node (PCA10001) to a host (PCA1000)
When the node is connected is should automatically send its address to the host....
