Hi All,
I am currently evaluating how I can charge a single cell with the nPM1300 PMIC with a USB-C connector, with the addition that the same USB-C connector should be...
Hi, on nRF54L15 Dev Kit, we are trying to validate our sleep current consumption. We are seeing sleep current of ~100-300uA, when it should be a fraction of that. As per datasheet...
I use nrf5340 DK as AP, nrf54l15 DK as TAG.
Below was uart print comments from AP
ESL_AP:~$ > esl_c bond_dump
esl_c bond_dump
Dump bonded device
ESL_AP:~$ > esl_c...
Hello,
I am implementing the Physical Activity Monitor Service which looks like this:
/* Physical Activity Monitor Service Declaration */
BT_GATT_SERVICE_DEFINE (...
We have an existing application that is based on asset tracker V2. It has been running since version 1.7.0 I have migrated to V2.9.0 a long time ago and it is running flawlessly...
Dear Team,
I would like to know if it is possible to add custom attributes and commands to standard clusters, such as the Occupancy cluster. I have reviewed the "Adding...
Data sheets
Where is the data sheet for the
NRF51822 SoC located?
I am also looking for the ARM
Cortex-M0 data sheet, where is
this located?
I need to find...
When I try to program an example with nRF go Studio from the new SDK12 or SDK13(fresh download) I get the following error:
It does not show up if I don't program the...
Hi nordic guys,
I used the ble_app_hids_mouse demo to build my generic hid device(no mouse and keyboard) project.Now i modified the hids_init() function according my hid...
Hi !
I work for about a year with a nRF52832 custom board without problem and recently I add a bootloader (with success) on the firmware.
Now I can't connect through...
My application is based on ble_uart_app. I want to integrate the DTM so that the nRF51 will be in RF test mode when it receive command from UART. However, I found that the...
Hi all,
We're going to implement floating point agorithms on the new chip which has a FPU (cortex M4F). with the 64MHz system clock, how many flops can we have? I could not...
Hello.
I use nRF52 & mpu9250.
I want to use dmp.
But now it's not going well.
Now, there is no error,but fifo_count doesn't change after fifo_count became 512.
I...
Hi,
sometimes not always, the function peer_id_is_allocated return false and this causes an ASSERT of device, because a NRF_ERROR_INVALID_PARAM is returned by pdb_write_buf_get...
Hi,
We're using nRF51822 and in the future we'll use nRF52832.
We do use bluetooth, but as far as I know, we don't use encryption (code is based on the HRS example, and...
Is nrf52 support 3 wire spi interface? I am using AD9837 3-wire spi module act as slave and nrf52 dk act as master. I am using SCLK, SSn(i.e.,Fsync) & MOSI pins only.I want...
Hi, I’m a newbie of nRF SoC. I have a BLE gadget with nRF51822_xxAC that controls LEDs and obtains data from accelerometers through I2C(TWI) devices. The hex file for the...
Hello,
I am able to get NRFtoolbox dfu code work for iOS 10.3. and now able to perform the DFU on BLE device.
But when I perform the DFU its GAP name changes from Beam...
Hi
I migrated from SDK11 to SDK12/13.
In SDK11 I already had avaiable a softdevice to use for ble_app_uart peripheral.
In the new SDK I have to build the softdevice but...
I'm trying to understand example "ble_app_hts" how after advertising make a connection. I didn't see in code any call of function "sd_ble_gap_connect" ? how is made connection...