Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello,
I am using pca10028 and sdk 12.2. I am trying to run some code. I am getting some make file error as ble_nus_error.PNG .
My main.c file is New Text Document (3...
Hi,
I have 2 nRF512840 eval kits and tried out the att_mtu_throughput example provided on SDK 13.0.
The throughput about 900-1000Kbps can be achieved with PHY 2.0 DLE...
Is there any way that I can use more than 4 timer in nRF 51 ??
(four or more...)
I'm using Softdevice 130, so It uses Timer 0,
and I'm using RGB Sensor using PWM Library...
i m new in NRF52832, i use saadc exemple pca 10040 sdk 13.0.0, i dont now how to get adc result from the buffer because there is 2 elements in the buffer :
err_code = nrf_drv_saadc_buffer_convert...
Hi, Nordic Forum!
We've been trying to implement an adapted version of the Secure Bootloader with Buttonless DFU in our custom board. We have successfully accomplished...
In this app by Nordic
github.com/.../Bluefruit_LE_Connect_Android
a cyclic redundancy check (CRC) is added to the payload byte array before writing it to the UART receiving...
i am creating a user interface using the sh1106 driver for a 128x64 pixel oled screen. so every screen is a list of items to be scrolled; however almost every screen i am...
Hello,
i'm currently researching the possibility of building scatternets with BLE. As the S130 softdevice supports multiple concurrent roles, it seems very possible (see...
Hi,
I'm using s140_nrf52840_5.0.0-2 and there are two characteristic for the peripheral, notification and indication. When I use notification to send data, I will get the...
Hello,
Are there examples of AES CCM encryption/decription?
Is there a recommended procedure for generating nounces?
Are there recommended procedures for using CCM...
Hi,
I have camera interfaced on GPIOs of nRF52832.. I am reading image data at the rate 80KHz.
Is it possible to write the data to SPI Flash (Slave) by DMA or by any other...
Hello,
I am using pca10028 and sdk 12.2. I am trying to add app_uart_fifo.c file to my code.
I have added the paths and also I have made changes in sdk_config.h. The changes...
Hello,
I am using nrf51822 / sdk10.0.0 / S110.
I write flash in SD / bootloader / application order.
I use nRFgoStudio and J-Link.
There are about 20% of malfunctioning...
