Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
i use demo ble_app_multilink_central and ble_app_multilink_peripheral ,in SDK 8.1.0,but when i use sd_ble_gap_connect (S120 to S110)return NRF_ERROR_INVALID_STATE ,
why?...
I am checking values of my PCB with an nRF51822. VDD = 3V. AVDD ~= 800mV
I was expecting a the AVDD voltage drop to be much less. What should the AVDD voltage be? What...
Hi,
I want to design one BLE braodcaster and one BLE observer using nRF51822 chip.
What should be the advertising interval time and receiving interval time (with receiving...
Hi:
I am using the ANCS from SDK9.0 ,SoftDevice8.0 and iOS8.1.3.
Every time when I run ANCS, SPI will often crash.and error codes is:NRF_ERROR_BUSY.
Don't know if...
Is there any extra requirements When a Android APP connect to my Ble Decice? I want connect to my Ble device(51822) by my Android APP(EZ-GUI Ground Station V3.208.208), But...
We have the bootloader working over serial at UART_BAUDRATE_BAUDRATE_Baud38400. We took a big leap and tried it at UART_BAUDRATE_BAUDRATE_Baud230400 and it failed. We will...
Dfu not working when i try to upload my custom made application second time.
nrf51422 sdk v8.0 and softdevice s110 on pca10028
the steps i used to do dfu are as
1)programed...
Dear all
I have some questions about nRF51822 bluetooth smart beacon kit, I read the User guide, but I can't get information about the following questions:
1、what is the...
I want to change bootloader start address BOOTLOADER_REGION_START to 0x33800 to store user data and DFU. But when I only change BOOTLOADER_REGION_START, my device can't work...
Dear Developerzone Board
Does the nRF51822 Sniffer just start with the conversion over all advertising channels or do I need to send a start command? Which command set...
The ENable pin on addition hardware component requires "floating" to power on, and drive low ( less than 1.25V) to turn off.
Unclear based on my understanding of the chipset...
Hello
Is there a way to stream data from one nRF51 device, to a second nRF51 and have the received data sent over UART to a host PC? Basically in my setup, I have a custom...
I'd like to understand why BLE_GAP_ADV_TYPE_ADV_IND is used while using a whitelist.
An example application that does this is the ble_app_proximity app. You'll see the...
Hi.
I need to use multiple SPI devices and I'm not sure which is the proper way to handle this, should I open/close each time the SPI port with different SS pin configurations...
