I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi,
I have been working with Bluetooth mesh. The test I have been performing repeatedly polls a single node and measures the RSSI (as measured from p_message->meta_data...
Hi,
I purchased Thingy:52 I want to develop ble mesh n/w application on Thingy:52.is it possible that I get any sort of support from you in this context.
I'm trying to run the Thread DFU examples on nRF52840, unfortunately I can't get them to work. On the client, I got the bootloader set up and ready, with the client application...
Hello!
I don't quite understand how to properly link NFC tag library (nfc_t2t_lib_gcc.a) to Segger Embedded Studio Project.
Steps I did:
Add nfc_t2t_lib_gcc.a...
Hi Nordic
Do you have a message sequence chart for how to do a Gatt Client Write with response? I can only find a GATTC Characteristic Value Write Without Response in the...
We are using the nRF6707 power profiler kit to measure our EVB’s current consumption in advertising mode. We use the example app ble_app_pwr_profiling. The only change is...
Hi,
Is there any example of adc (saadc) and uart throw ble?
I want to take same measurements from fotoresistor and send data via ble_uart i found same example but no...
I have a problem in selecting inductor(L1). In NRF52832 IC datasheet, mentioned specifications of inductor L1 are: 3.9nH, 0402 high-frequency chip inductor. What should be...
I am writing a bluetooth mesh application with a server and client.
Provisioning is working, but the configuration of the server is giving me problems.
I have based my...
Above image is our design for nRF51822. Design also contains Accelerometer and WiFi (ESP8266).
My problem is, I am not able to see nRF BLE advertisement while scanning...
Hi!
Can someone please help me debug this example. It used to work, then I changed number of peripheral links to 1 (to see what RAM suggestion would be), then returned it...
Hi!
I try to flash nrf52 from keil and message appear:
The firmware of the connected J-link (S/N: xxxxxxxx) does not support the following memory access: Read @ 0x02000004...
Hello,
I want to enable UART only when data transfer is necessary.
I am using nrf 52832 and sdk 14.0.0.
I am using "ble_app_uart".
I could not find the answer I...
Hello everyone.
I have a question about sleep_mode_enter() behavior.
I'm using nRF5_SDK_12.3.0 and nRF51822 for my project.
I put a lot of printf statements in the example...
