Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi,
Is there a uart example for the NRF51 Dongle(PCA10031)? If not, how would I go about implementing uart on the dongle to connect to the Android NRF Uart app?
Tha...
Hii all,
I would like to create a project that take an input from any Bluetooth device and display it on display device like EPD. Till now I just hard coded the image and...
Hi all,
I have two NRF24LE1 devices, device_A for send data and device_B for receive data, the protocol data included in a 10-bytes length arrary(buffer).
In device_B...
I'm trying to understand whether my callback assigned to the data_handler variable during initialization of the Nordic UART Service gets executed in an interrupt or somewhere...
I know there have been a ton of topics about this but I've tried pretty much every solution I can think of and I cannot seem to figure out why my sleep current is consistently...
Hi,
I'm facing a very critical issue.
I need to send a time critical data from a ble sensor device to a Camera device acting as a ble central device.
Due to lack of full...
I want to send data without a computer from 3 ADC sensors.
using de ble uart.
How do I set my variable to send data?
I should use in ble_nus_string_send(&m_nus, data_array...
Hello, I am trying to follow the instruction for a 2way communication between nRF chip and the client device (cell phone). Although my chip is nRF51422/ PCA10028, I have found...
hi all:
Recently, I use nrf51822 as a central to connect some older sensor, but the ble chip of the older sensor did not use nordic, so I have this problem. I develop the...
I have the Heart Rate Service(HRS) program written in embedded c. I connected a two LEDs to nrf51822 board. One LED will start blinking when advertisement starts and other...
How do I write a value to gpregret when flashing the chip?
Basically, what I need to do is be able to detect the first time the chip is powered on so I can go into a special...
In my device I want to adjust the slave latency connection parameter, however my desired min-max connection parameters are the same as during the initial connection. I find...
I have an imuduino (arduino board with nrf8001 bluetooth and some sensors) board and am trying to load some of the profiles from the nordic arduino nrf8001 bluetooth api on...
