Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I am testing this on ble_app_hrs and ble_app_hrs_c. After devices are bound I would like to skip discovery as it takes long time. So all I need to do is get the service's...
After I receive data by ble_nuts,using example ble_app_uart.
I call ble_nus_string_send to the central, however I got error,I print error code is 8 which means "NRF_ERROR_INVALID_STATE...
hi
First,I apology for my poor English...
I want to make a project to connect 2 device.
With a sensor from TI , which comes out the sensed signal .
Transfer the data...
Hi,
platform info:
SDK 9.0, NRF51822, SD:s110_nrf51_8.0.0, Master Control Panel(android):2.0.0
We use eample dual_bank_ble_s110 under dfu/bootaloader/pca10028/ of SDK...
Hello,
I've built "bootloader" project in sdk6 and sdk8, which named "sdk6_bootloader.hex" and "sdk8_bootloader". Then what I did are listed as below:
(1)
using ...
I am trying DFU with:
BOARD_PCA10040,
nRF52_SDK_0.9.2_dbc28c9
s132_nrf52_1.0.0-3.alpha
One interesting thing is the SDK_0.9.2_dbc28c9 can not work with
...
Hi,
We currently (no pun intended!) don't have any battery protection circuitry for reverse polarity designed into our prototypes. Our device is powered from a CR2450 coin...
Dear Nordic.
I read specific data using GPIO(timer sampling), BUT, occasionally, the data is broken because of Softdevice interrupt.
So I want to guarantee it while reading...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Hello everyone.
I would like to ask if is possible to compile and run examples from latest IoT SDK 0.9.0 on pca10028 board. Every example has only Makefile for latest pca10041...
Dear Developer Zone,
I'm using an nrf51822 with SDK8 & SD S110 v8
We have an iOS app connecting to a custom service on the NRF device. What we would like to do control...
hi,
i have a project which need dfu by OTA,but nrf51822 flash is not enough.The project detail information in the following:
chip:nrf51822QFACA10
SDK6.0
SOFTDEVICE:7.3...
