We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Dear all,
I was following the "Getting started with the nRF52840 Preview Development Kit" page. But when i connect the board to the computer, the board do not appear as...
Is it possible to change the output power of the Thingy to +4dBm and how would one do that.
We are using the Thingy for demos and would like to demonstrate the difference...
Hello:
I have been trying to figure out the proper app ram address base by calling sd_ble_enable.
I am using keil's debug mode, and when the program hit the breakpoint...
Hi, I'm trying to view some logging out put using the segger RTT viwer whilst running keil's debug mode.
I can view some, incomplete loggins in run time (meaning not all...
I find NRF_UICR->PSELRESET[0],[1] can't be written to 0xffff when their values is 0x0015, but the values can be written to 0x0015 when pre values is 0xffff.
so, I can't...
I try to get rssi , but it didnt work. I tried to control what is the problem? , I just want that ; if there is any change , My red led will blink and then I will controll...
I am using Blend Micro with Nokia 5510 LCD.
Before applying BLE SDK for Arduino, LCD works fine.
After initializing BLE UART for nRF8100, send text through nRF8100 by UART...
sorry for short question
almost first step here. I came from eddystone format beacon to here
but I've found long time to add a sensor on nrf51822 module..
some articles...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
when i am load the the program to my nrf52832 with ble lbs example it show an error : Flash Download failed - "Cortex-M4" . my softdevice is s132 v3.0.0 .... please help me...
Hello everyone,
I have tested my prototype on nRF52840 but the board is pretty big and I want to do a product pilot with a custom hardware of mine. Now I know that the...
Yan,
To test my UART program, I'll need a phone which will receive my GATT MTU, such that I can test it.
Do you have such Demo app, preferably for a Windows phone, or...
Is there any simple way of reading analog values from pin. Setting up SAADC is giving too much of errors like command line action failed or any variable is undeclared whose...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
