Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello, I am toggling two separate pins at different rates but it looks like for whatever reason the when I go to clear one gpio register it clears everything. I understand...
Hello,
I would like to make use of white list advertisment for my heart rate application on my nrf52832 s132 pca10040, currently I am using SDK12.2, is there some example...
Hello,
I used translation software.
I'm looking into LDO mode and DC-DC mode.
However, I did not know what LDO mode and DC-DC mode are.
What are LDO mode and DC...
I'm working on a project that will utilize the nRF52832 as the Host and Controller and an STM32F3 as the application using serialization.
I've included the nRF5 SDK V14...
We just produced a PCB with a NRF51822-QFAB-R7, does Nordic provide a EMC test firmware that we can flash onto the chip? Basically need it be always transmitting....
Thanks...
I'm using the original BLE App UART from nRF5_SDK_14.0.0 on a PCA10056 Board.
The board is advertising, but if I want to open a BLE peer-to-peer connection, than the application...
With SDK 14.0.0 and Softdevice 5.0.0 I have problem with Windows 10 connection. The device connects to PC but then almost immediately disconnects with reason 0x13 (BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION...
Hello,
We developed a few devices using the nRF51822 and noticed that the receiving range is reduced significantly from our nRF24L01 devices. The transmission range is good...
Hello,
I'm trying to measure the current profile with the PPK (HW Rev:1.1.0, SW: 1.1.0) but I see a lot of strange behaviors.
My firmware initializes everything and the...
I am running a nrf52840 dev board as an NCP connected to a RASPBERRY Pi running wpantund.
I have 10 other nrf52840 devices in the network. The PI has LIBCOAP coap-client...
Hi,
Just curious to know if anyone else had this issue and how they solved it.
My colleagues and I are working on code based on the Nordic Uart Service, in SDK13.1.0...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I am using 3 uarts for my applications using nrf52xx, i want uart without fifo,i configure 3 uarts independently and use the
#define APP_UART_INIT(
P_COMM_PARAMS,
EVT_HANDLER...
Hi Nordic forum.
We wanted to update the bootloader over the air. Initially, we had a very plain bootloader (the one provided in the example) but later we added a timer...
