I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I have nRF 52 DK board and nRF 52832 breakout board. I need to program my nRF 52832 breakout board. I tried example devzone.nordicsemi.com/.../ and devzone.nordicsemi.com...
I modified the HTS service to send notifications and read property at the peripheral. It notifies the simulated temperature every 1 sec in Celsius type. I tried writing HTS...
Hi,
I want to know what kind of antenna nordic recommend to use with NRF52 chips.
Please could you guide us about it. We are interested in some sort of table where we...
hello,
having everything working on the nRF52 DK i tried to migrate to the smart beacon kit (pca20006 with s130) but somehow cannot bring up a proper peripheral configuration...
Story and Official Code Test Passed
I am trying to integrate BLE into Smart-Lock and LoRa Terminal . So I build a custom board with off-the-thelf modules to evalute and...
I am current develop a "Surface Dial" hardware compatible device. (nRF51/S110)
Everything is ok but the host PC will freeze about 30 secs after my device wake-up from sleep...
I'm working on a product that is somehow related to geolocation. As part of it, RSSI measurement is sent back at high frequency to the central. Currently based on nRF51822...
Newbie here hoping to get some direction on how to properly setup a timer to have a timestamp displayed for DEBUG messages. I am working on a PCA10040 board. I tried looking...
Hi,
I have some basic doubts in installing the power profile on nrf52Dk(nrf52840). I'm trying to use it on my central device which has its application FW running. I have...
what is the sending data rate of the sd_ble_gatts_hvx() ,why i use sd_ble_gatts_hvx() send data 600Byte per second, it lost data again . it can be use yes or no ?????????...
I can copy a Hex file from a Mac to the mbed USB drive and the code executes correctly. However, if I upload the hex file from any windows PC in our office (Windows 10) the...
Hello, I am trying to generate pulses with the nRF52832 chip.I created a basic setup for test purposes; I simply connected a LED to the PWM output, but even though I put 0...
Hi,
I have designed the Circuit using NRF52832 BLE and AT8010-E2R9HAA RF ANTENNA and tuned the circuit accordingly. Since the antenna was not available so I placed other...
I'm relatively new to development on the nRF52832 and I'm trying to find information on how to use the sleep mode with the SAADC.
Goal: The micro should be in sleep mode...
