Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hello,
I need do synchronize the time between two NRF52 devices. One is connected to the other by a custom BLE service. Do you have any ideas how this could be done?
...
I'm trying to integrate buttonless DFU with secure bootloader with bonds with the DFU.
Using SDK 14 with SD 132 v5.0.0.
Using projects: secure_dfu_ble, ble_app_hrs_freertos...
Hello:
When I try to open an example project from nordik, keil doesn't open some files and I get the following error:
"no source": Error: #5: cannot open source input file...
in main() I initialize the timer
// Initialize the clock module
ret = nrf_drv_clock_init();
APP_ERROR_CHECK(ret);
// Request the low-freq clock to start N/A for SoftDevice...
SDK v12, SD130 on 51822.
I init uart through APP_UART_FIFO_INIT, and installed uart_event_handler. UART rx/tx with an external MCU works OK while softdevice running.
...
Hi. I have some nRF51 firmware I'm migrating to the nRF52. It's a peripheral with bunch of vendor specific services, using SDK 13.0.0 and SD 132 v4.0.2.
My code builds...
Dear Nordic,
I am trying to send the sensor data via beacon. I am regularly updating the manufacture data (through which I am sending the sensor data). But while executing...
In fact,there is a demo on internet, and I test it ,but I found that the event is not reliable! my code is :
static void my_fds_evt_handler(fds_evt_t const * const p_fds_evt...
After some effort, I have managed to build the beaconing example that's missing from the examples.emProject of the ble_mesh_v0.9.1-Alpha SDK. I have this running on the PCA10028...
on the download page for the command line tools, the version 9.6 is showed but the download link points to 9.5... can we have the 9.6 where it says 9.6? Thanks!
I have a question on the supervision timeout: suppose that the slave latency is set to be 0, the CI is set to be 500ms, and the supervision timeout is set to be 4s。Once there...
Hi - I am following this tutorial and getting this error.
This exact question was asked; however, I do have the mkdir file in the C:\Program Files (x86)\GNU ARM Eclipse...
Hello,
This is less a question and more of a survey. We've recently completed development on a project using the nRF51822 but have run into an odd power problem. We built...
hello,
i am using the nrf52840 preview devkit and am currently trying to find a solution for timestamping / for a time-base. the idea was to use the RTC for that since...
