Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
I am trying to use BlueZ in "Raspberry Pi 3B" to connect my 51822/52832 device.
My Hardware is Raspberry Pi 3 model B, and use internal bluetooth interface, the OS...
Hi Nordic gays guys,
After our 51822 firmware added the Service Changed characteristic.The Android OTA GATT_ERROR issue was solved.But there is a new problem in IOS.After...
Hi,
Find big problem with GCC make settings (guess Makefile.common) does not work with SDK 15. with SDK 14.2 same Project works succes.
The Problem : use SDK15 , the...
Hi,
Not directly related to Nordic, but I as many people are doing the same I figured it's fine.
is there any reason why this would not work? assuming the I2C is already...
Hello,
I just bought an nrf51822 evaluation kit and a segger J-link BASE Jtag. I understand that I have to play with the SW4 swith and the U4.
I identified the switch...
Hi
I am trying to setup my raspberry pi to receive message from Arduino using C++ code. I am getting a below error message. pi@raspberrypi:~ $ sudo g++ -Wall -Ofast -mfpu...
Hi I just have a simple question and that's where the code keeps Bluetooth mesh control how many devices it has in its stack that it has provides keys to. for every time I...
hi
sdk 15.0,
IN Multilink, 15 devices is operate normally. However, changing the device to 20 causes problems.
Is there a way to fix the problem?
attached source ...
Hi,
I was trying out the long range example provided on the NordicPlayground GitHub repo, and worked great when communicating between two nRF52840 dev kits. I however noticed...
I know that the the +/-250ppm LFRC accuracy is required for BLE... but is that just for a system that receives data? Is there any need to calibrate for a system that only...
Hi all,
I am using PCA10040 with nRF5_SDK_14.2.0 and using the ble_app_uart example.
Basically I have a large array of size 18750 to send out and having read on the forum...
Hi Dev Team,
I would appreciate if you can help me sort out the errors that I am getting when doing a DFU OTA using the 52 Dev Kit to the Thingy. I basically followed...
I have an input connected to P0.18 on my nRF52832, which needs to be driven high by an external source. I am running into two problems, which may or may not be related:
...
Hi,
I have seen some posts from
Ole
and
Hakon
about the bulk data transfer. But I have some confusions which I want to clarify before implementation.
I need...
