I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Using the sdk15 and softdevice 132 v6, I'm setting up an app to read and write to an SD card that uses SPI1 (SPI0 is used by a display). Everything is working great, except...
Hi,
What's is the max length for the payload data in "mqttsn_packet_sender_publish" method?
EDIT:
Redefining my question above: What's is the max length for the payload...
Hi Sir,
According the table 19.4.2 of 52832 datasheet (v1.4), there is a start up time (0.36 ms) for HXFO.
How do I measure the start up time of my 32M crystal?
If...
Hello,
While an attempt to develop solid security mode bulded around Root of Trust starting from RTL and Device root key we found that unfortunately, it is mentioned in...
I would like to detect if a reset happened due to a brownout or an actual power off.
I tired so far using the GPREGRET and RESETREAS registers. They are useful to detect...
I have an app that works perfectly when run from the debugger, but not when started by HW reset. We use the serial port to communicate to a control processor (STM32) The Nordic...
Hi,
I was trying to test a slot circle antenna with nRF52832 which is well matched to 2.4G~2.48GHz, but it is circular polarized antenna with high directivity.
However...
Hi All!
I use nrf51822 with sd s110 to send data to android phone with sd_ble_gatts_hvx. If sd_ble_gatts_hvx returns NRF_SUCCESS then that packet get to TX buffer. I didn...
With nRF5 SDK v15, the code size became too large for the free version of UV5 , Is there a way to reduce the code size by reducing some array size or commenting something...
Hi There,
I'm stuck with Getting BLE uart working in another example.
I wasn't sure if converting the BLE Uart example into a central/peripheral application would be more...
Hi.
I want to read thingy's sensor data. I'm using nRF52840 DK.
I have tried using ble_app_multi_link_multi_role example, but there are only read button state.
How can...
Hello everyone !!!
I've recently started working with Segger Embedded studio for nfr52840. I want to add a new driver into an existing projects.Let's say GPIOTE
I...
Hello,
Recently i am working on UART application on nRF51822 based product.
In UART application code, there is no option to configure the modulation rate.
So, I would...
Dear friends,
if i adjust the tx power of nRF52832, e.g., by calling sd_ble_gap_tx_power_set(), which phase of the current will be affected in the pic bellow? just the phase...
