In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I am porting my own RTOS (named PicOS) to nRF52. So far, PicOS can run well without activating SoftDevice. I mean the SoftDevice is programmed on the flash memory but not...
Hello All,
I was doing some development on the Nordic nrf51822 and it was working fine without any issues.
I tried to remove some functions from the main loop (not removing...
Wich is the proper way to bring bootloader into deep sleep?
I'm using a modified version of the BLE Secure DFU Bootloader (SDK 14.1.0) for the nrf52810. I have added button...
We are working on non connectable beacons without any external I/O. They simply have a power and ground. Is it possible to perform OTA updates on such devices. Is there any...
Hello,
I am trying to use the extended advertising mode available on the V15 of the SDK (with SD S140 V6.0.0). I use the template example where i am currently advertising...
Hi,
I have developed part of my code using UART, starting from the UART example in \examples\peripheral\uart , but before continuing I need to start doing things over USB...
Proxy Error
The proxy server received an invalid response from an upstream server. The proxy server could not handle the request GET /index.jsp .
Reason: Error reading...
HelloI have to evaluate if we can start development with long range (coded phy). I like to see how fare away two devices can be placed to find them (long distance advertising...
Hi,
I am implementing ContikiOS on my custom nRF52823 board. I have been following the instruction here: github.com/.../README-BLE-6LoWPAN.md
I am running Debian 9 testing...
Hi,
I am trying to use the p21 reset pin as gpio but it is not working as expected. it is showing a 3.3v even when i am trying to toggle the pin. I have removed the CONFIGURE...
Hello,
I am just starting to develop on nRF52840. I want to use the USB functionality. Could you please let me know how to get the Vendor ID and Product ID?
Kind regards...
Hi,
I am trying to use the bit counter to get an indication about the length of the data I am sending.
After trying around for a while it turned out the value of the bit...
Hi
I'm using S132 V5.0.0 with the nRF52832.
I tried to add an include declaration to the last added primary service by using BLE_GATT_HANDLE_INVALID as service handle...
Hello Everyone
I want to interface an external flash mx25r6435F with nrf52832. i ll be writing and reading some data. It should be spi .
Can you guys please suggest me...
Hi, everyone, We develope the BLE project on nRF51822 tool that uses the ADC. But the read measures are different from IC to IC. At the link devzone.nordicsemi.com/.../how...
