Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi;
I using experimental_ble_app_buttonless_dfu as the project. After build the project and download with softwareDevice , it works ok . Then I compile bootloader_secure...
Hi
I have done setup using guide ( https://github.com/sandeepmistry/arduino-nRF5 ) by sandeepmistery.
I am able to blink led of nrf52DK using Arduino example code. ...
When i choosing among the 52832 and 52840, i found this table.
One point i am not sure, i believe the 52832 stack is already support Bluetooth 5, but why the table said...
Hello,
I would like to manage time (hours, minutes, seconds) on NRF52 chip: what is the best way to do it ? How to use as less energy as possible ?
At the first connection...
Hi all,
I'm new to Bluetooth technology and just start some test for indoor localization using 52382. But I find out that 52382 does not support the long range feature of...
Hello all,
I'm curious if anyone could lend some thoughts.
I'm just in the research stage and going through a few examples but getting a little overwhelmed.
I'm trying...
Hi,
I am using nRF51822, S130, SDK 12.3.0
Want to use is low power failure warning. using the following code.
However, when break on line err_code = sd_power_pof_enable...
I am currently using a CSR 4.0 dongle 8510 A10 chip on Windows 10 Creators update
I can get it to Pair with the nRF52832 in windows, according to windows.
I have a ...
I am upgrading an existing project that was working on SDK 14.2.0 with S132 5.1.0 to SDK 15.0.0 with S132 6.0.0. I'm using IAR 8.20.1, and have made the changes suggested...
Hi,
My aim is to transmit the beacons. iam using nrf51822 usb dongle and nRF5_SDK_12.1.0).I need to run E:\nrf1\examples\ble_peripheral\ble_app_beacon\pca10028\s130\arm5_no_packs...
Hi All!
I use SPI with ss_pin = NRF_DRV_SPI_PIN_NOT_USED. but seems it doesn not work properly.
in the file nrfx_spi.c , the following code exist to init ss_pin during...
Hello,
I am using a nrf51422 in my work. I am focusing on reducing system power consumption as much as possible.
Q. When a peripheral (server) starts advertising (and...
I am about to develop a Bluetooth Mesh network with the nRF52832.
With the PCA10040, i already able to form a Bluetooth Mesh Network, such that there is one client act...
Does anyone know where I can find a list of which phones/tablets support Data Length Extension (DLE)?
We are finding that many budget phones (e.g. Motorola G6, Samsung Galaxy...
Hi,
I'm using nRF52840 (rev 1.0.0) and Mesh 2.0.1 and SD 15.0.0.
I added FreeRTOS following the example "hrs FreeRTOS".
In FreeRTOS, the source clock (configTICK_SOURCE...
