Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello!
I have been trying to implement the serialization for STM32L476. During my development I discovered that the deserialization of the SD_BLE_GAP_ADV_SET_CONFIGURE response...
We have a custom board with nrf51822 chipset, and we need to implement the firmware update process, which can support both over-the-air and uart type firmware update.
1...
Hi, we are contemplating moving an existing application to a nordic chip, the nRF52832.
https://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf
Our previous CPU uses...
I'm in the process of implementing a custom layer above ESB in order to allow more than 8 devices to communicate with a receiver (By tagging packets with a device ID)
I...
I used nRF52 SDK V15 and tried to load the sample BLE HID apps into the nRF52-DK Development Board.
I tested both ble_app_hids_keyboard and ble_app_hids_mouse. Both apps...
We have exiting BLE 4.0 device, which should be updated to the mesh. nRF52832
In the DFU for BLE4.0 you could update the booltoader and the softdevice with one update, with...
Hi All,
I am working on fatfs example from sdk 12.2.0 on pca10040, nrf52 dk, nrf52832. And i did not change anything in the code but it seems that my sd card is not getting...
I started with the template app and added BLE services, and I'm continuing by adding a TWI sensor (I2C). I know there is a TWI_sensor example, but I already had some working...
Dear All,
I am working with nRF52840 product. According to my scenario i have 1central unit(master) and up to 19 peripheral unit(slave).
I downloaded SDK 15.3.0 ble_central...
Hello, I am evaluating ways to enter the DFU mode when application is corrupted (i.e. it does not reach the code for entering bootloader).
The documentation states that...
Hi
I'm working on a IoT solution with a small circular board, 26mm in diameter. I was suggested by Johanson to use the 2450AT18D0100 antenna and a lowpass filter designed...
Hi,
I am new to this nrf development, I have been working on the SDK 15.1 on the nrf52832, with softdevice 6.1. I found these examples in the SDK very helpful. I have to...
Hi,
I am planning to send an analog signal to the nrf52840 dongle pin and send it through bluetooth to mobile app. I am thinking of merging ble_app_rscs and saadc together...
