Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I'm currently evaluating the nRF9160 chip as a potential replacement device in our internet-connected products. In most cases the zephyr documentation and examples are...
Hi,
I modified your USBD BLE UART Example by commenting out the button and LED code to run on a dongle with J-Link debugger soldered on.
I removed the bootloader and set...
Hi I am new to NRF52832. I am using SDK 16, Multlink Central (ble_app_multilink_central).
Here are my questions:
1) The software keep resetting when I flashed the code...
Setup nRF52840 DK S140 nRF52 SDK v16.0.0 nRF SDK for Mesh v4.0.0 Goal I would like to be able to disable the Mesh stack and all radio operations so that my application can...
Hi,
[Softdevice 6.1.1]
I am developing an application which uses the radio timeslot api in conjunction with BLE. Even without starting BLE advertising, or any other BLE...
I did some evaluation on nrf9160dk recently. I try to run some at command to control lte modem, but some wired thing happen.
After I introduce at command in to one work...
Is there is an option to change the payload of NFC t2t after setting the payload.
So the requirement is once there is a polling device is in the field, we need to change...
In ble_app_blinky_pca10040e_s112 example, Generic access service has read and write permission.
When writing the name, I want to handle this event and change the advertisement...
Hi Team,
We are using nRF52840 DK with the latest SDK 16.0.0. We know that SDK have multiprotocol support for BLE+thread and BLE+zigbee. Its okay for that and we tested...
Hi, i have been trying to get GPS and HTTP to be able to work with eachother, but im having some struggles.
After the GPS starts, the program begins spewing out "Invalid...
Hello,
I have exercised the flash driver and that is working fine. I want to save a certain value into a specific address in NVM and I want that part of the .hex file. I...
I just upgraded to SES 4.42 from 4.30a and I'm getting the following compiler warning for file zigbee_cli_cmd_ado.c "Taking address of packed member of struct zb_af_simple_decs_1_1_s...
Dear Sirs,
I am using example anr_hrm nrf_sdk_15.3.0 I would like to use PINs on/off
software s212
#include "nrf.h"
#include "nrf_gpio.h"
#include "nrf_delay.h"...
Dear All,
I am using (nRF52840) in one of my design.
Application program we have taken examples\peripheral\usbd_ble_uart\pca10056\s140\arm5_no_packs code as base code...
Hi,
Good Day!
Statement of Problem: We are using SPI to transfer data to custom LED matrix which uses HT1632C led driver. For strings more than 7 character length we used...
