This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hello,
Every time I try to run any example I download online for my nrf52832 board I get dependencies errors after locating the project folder to the sub "examples" folder...
I am trying to get battery % from the thingy91. I have the AT command AT%XVBAT running successfully. It returns what I assume is millivolts. However these value are higher...
When testing different applications on an nRF52840 dongle I have the following problem: The table of service and characteristics (1 service and 4 characteristics) of an earlier...
Hi I found one example project named "serial" that implemented UART over USB:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.3.0%2Fgroup__nrfx__saadc...
I've gotten the SAADC working in a blocking fashion and been able to evaluate sample times. Now, I'd like to set it up to automatically read three inputs in a row to see how...
Hi There,
I am curious to find out if the MDBT42Q module(s) can be used as a single master to multi slave setup? Essentially I want to have one module setup as a master...
Using LFRC as the softdevice LFCLK source, enabling and running the WDT causes the softdevice to hang until the watchdog reset when calling nrf_sdh_disable_request . This...
Hi
I'm trying to send fixed AT commands to the modem using a code based on this code from Rallare: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples...
Hi
I'm using a SparkFun Pro nRF52840 Mini which has a UART on PIN 17(TX) and 15(RX). I've written a very simple piece of code to blink the onboard LED on and off and to...
I update my software on the nrf52840 to the SDK16 and softdevice 7.
to get this software running i update the device family pack to version 8.29.0. (keil)
If i build the...
Hi,
There's no description at all in either the written text (31.3 SPI master transaction sequence) or the timing diagrams (Figure 71: SPI master transaction) showing precisely...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
In our setup we load merged hex file...
from this link
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
I gathered that nrfjprog is for flashing...
