We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hi Goature,
We are also try to implement the same. We aren't getting any idea how to start. Refer the same thread : devzone.nordicsemi.com/.../make-ble-central-send-firmware...
Hi there,
Is there any Zigbee Motion Sensor code example that someone has put together? I could not find any on the nRF5 SDK for Thread and Zigbee.
Thanks
Hello,
Was programming two different boards today with the new 1.1.0 modem firmware.
Programmer reported the following for the two boards.
2019-11-21T21:10:34.297Z...
Hello!
Some time ago you seem to bundle sample 5 x nRF52832 to nRF52DK. Recently there was no bundled chips. Why did you change that?
The development and prototyping...
Hello, I tried to set up my nRF9160 with this tutorial and there is a problem: https://www.youtube.com/watch?v=jZQcmU3KIMY&t=216s
According to the tutorial, LED 3 and the...
I'm investigating the PDM peripheral on the nRF52840 and I have not been able to find out what the RATIO configuration bit actually does.
Presumably it controls how aggressive...
Hello,
I try to solve one problem with SYSTEM OFF and I still have no idea.
In my device I have one button switch and with this button I need to change characteristic...
I am using nrf52832 modules connected in mesh light switch example configuration from mesh V 3.2.0 i am unable to send a array over mesh i have gone through various posts...
I wanna know that, is latest SDK has demo example which will convert nRF52 SoC
to act like basic 2.4 Ghz transceiver (who should by default remain in Receiver mode &
switch...
Hi guys,
My question is really general: How do I reduce the TX Power of an nrf51822 BLE beacon?
The situation is the following:
1. I ordered this device: https://www...
We have a problem on our test system: it cannot communicate with our DUT on ATT level after 30 seconds.
Our DUT consists of a NRF52840 with SDK 16.0.0 and softdevice S113...
I have an issue with the NRF beacon code combining with the NRF rtc code.
I want to set up a bluetooth advertisement with an incrementing value. Therefore, want a timer...
Hello,
I am using ble_app_uart example in nRF SDK 15.2.0 in which I have included "nrf_drv_gpiote.h" and initialized gpiote as follows:
After making this change, the...
Hi Devzone!
I'm planning to integrate fpu_fft with ble_app_uart, and did it.
I wanna use IRQ of fpu_fft but I can't find where I should define fpu_interrupt_mode.
...
