I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear all,
Our application is made of
Chip nRF518122 + SDK 11.0.0 + DFU Bootloader + BLE application (gcc complied) loaded with nRF Toolbox over the air
we are putting...
Hello,
the nRF9160 product specification 1.0 states in 5.1.4.2:
"Note: The LTE modem requires using LFXO as the LFCLK source."
I checked the clock register and noticed...
Hi,
I have developed an SWD working code which read-write the Flash Memory and RAM which is working very good.
Now I have a problem in I need to write start address...
Due to time pressure, I'm starting this thread based on an existing ticket: https://devzone.nordicsemi.com/f/nordic-q-a/51423/firmware-on-custom-board-application-bootloader...
Hi team,
We have a customer who has some questions about GPS.
The questions are:
Where do we save the Ephemeris data when GPS code start? RAM or flash?
When use...
Hi,
Can an nRF5x device be configured as a BLE relay with Bluetooth Mesh?
I believe with the Central-Peripheral-Relay example, the Relay needs to establish connection...
Hi. I am trying to create a dfu zip file that contains the softdevice, bootloader, and application. I am DFU upgrading an NRF52 device from SDK v13 to SDK v14 via Nordic's...
Hello,
we are using the nRF52840-DK.
File: secure_bootloader_ble_s140_pca10056.emProject
File: ble_app_buttonless_dfu_pca10056_s140.emProject
In short, we are...
Hi,
I have a well working cli environment under linux where i can compile, program and debug a nFR52 demo board.
I have installed RSSI Viewer (1.05) and Bluetooth Low...
We want to deactivate Mesh DFU packets relaying from the App side to avoid messing with the bootloader firmware. Is there any flag we may use for that?
Hi,
I'm trying to use a Bulk IN endpoint (EPIN3) and am running into an issue.
I call the nrf_drv_usbd_ep_is_busy() function to test whether it is safe to proceed with...
Hello
I am using buttons less DFU,
S132_nrf52_6.1.1 softtdevice
using Android + nrf connecct, I can update the device with DFU
using IPhone 6, I can not update...
I am able to provision using BlueZ's meshctl tool on Raspberry Pi3. However, after restarting meshctl, I am not able to control my device. I tried the "connect" command after...
This isn't exactly a question, because after like...8 hours of debugging, I figured it out. However, in zephyr/samples/bluetooth/mesh, it defines a hardcoded device uuid ...
