Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I have taken a new Thingy:91 out of the box, fitted ibasics sim card and been through the registration process. Sim registers fine, but the 'add new LTE device' does not recognise...
Can you tell me which Heart Rate monitor gives 0x2A37 is the UUID for the Heart Rate Measurement characteristic. The heart rate service is 0x180D. Battery service is 0x180F...
How can I add debug and release configurations to the "mqtt_simple" project?
Video tutorial "SEGGER Embedded Studio - Build configurations" does not show this important...
Hi Devzone!
I'm using nrf52840 custom board to launch iot service.
We have two type of devices. One is master and the other one is slave.
For now, both of them...
In nRF5 SDK 16 (downloaded file nRF5SDK160098a08e2.zip), the components/boards/pca10059.h file is missing the LED_START and LED_STOP defines that are present for other boards...
Dear Nordic,
I have a 4MB external flash on my board, I've successfully run the code on it by using XIP. However, I got stuck when I was trying to read back data from...
The bug shows when executing an application in RAM with nrf52840. Using SDK 16 but seems to show in older versions also.
The below function code is the first level of...
Hi all!
Everywhere it can be read how important the dimensions of the groundplane are for a well working antenna... but what are the right dimensions? And where is the best...
Multilink S132 central should handle connections to multilink peripherals which do continuously advertise. Once central got first adv event from such peripheral it establishes...
Hey,
As a student currently I'am working on a project for my universitiy. I want to use the nRF51822 for Bluetooth low energy communication.
In the datasheet is written...
Hello Everyone,
I'm involved in a project where we are evaluating ble mesh and Thread mesh on nrf52840.
I want to know, does Nordic supports ble mesh and Thread mesh simultaneously...
When using Keil Compiler, I am unable to compile any of the ble_peripheral examples. I get an error that says...
RTE\Device\nRF52832_xxAA\system_nrf52.c(29): error: #5...
Issue with NRF52832 Firmware installation
Hi We are developing custom boards with nrf52832 chip, and it is working well.
The issues occurs when installing firmware without...
Hi,
as i mention in https://devzone.nordicsemi.com/f/nordic-q-a/44924/dfu-serial-failed i have f ramming error now and then when i do DFU over serial.
My idea was to write...
Hi,
after I received the thingy91 I wanted to connect it to the cloud, as mentioned in the get started.
But when I want to add the LTE Device, it shows the following Error...
