I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Hello.
Im tring use nrf_dm sample with nRF5340 on nRF Connect SDK V2.9.0, with a custom board.
I got the error when I try dm with other device:
my prj.conf:
...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
I have been trying to implement a way to wake the system up after doing sys_poweroff() but no matter what nothing seems to work. I already tried many examples and none of...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
I want my peripheral device to act as a beacon while it is in a connected state with a master device. Is it possible to start not-connectable advertising in parallel with...
I am working on a nrf51822 UART bootloader using Keil 5.14 (though I had the same problem with 5.1). If I start with the pack example dfu_dual_bank_serial_s110_pca10028 with...
What happened to NRF_FICR_Type.INFO and FICR_INFO_Type in nrf51.h?
This was in ./components/drivers_nrf/hal/nrf51.h in nRF51_SDK_7.1.0_372d17a
but is missing from ....
Using the nRF51422 with the TWI hardware version. Just playing around to verify signals with the following code which just configures the TWI1 and then repeats continuously...
Hi,
i tried to update the firmware of nRF51-DK but it crashed and now Keil uVision says "Cannot find the JLink version number"
Its also not showing in the nRFgo stu...
I'm developing application using your devices (PCA10001/PCA10000) and S130 SoftDevice. I tried to implement DFU/OTA feature in my app. For this purpose I used DFU sources...
Hi All,
Does anybody has a working setup using SD 7.1.0 with SDK 7.2.0, iOS 8, DFU with a secure connection?
When I use no encryption it works, but when I enable encryption...
So I'm currently trying my hand at some very simple things that one can do with the NRF51-DK.
One of those things involves sending notifications to a client on certain...
Hello,
I'm testing n51822 with low voltage mode, and want to check the BOR condition.
Is there any threshold for brown-out reset, or voltage tolerance? e.g. 1.68V...
Hi.
I have received down the source of the example of experimental_ble_app_uart in my keil.
I use register.(NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;)
but, Hardfault occurs...
Hi there,
I am currently using the nRF51 DK trying to teach myself how to create a working ble application. I am currently going through the application note nAN-36_v1...
Hello!
We are using an BLE NRF51822 chip as a GATT-Server, unfortunately without any possibility to modify its software at the moment. The BLE-setup should be very similar...
I want to run the Direct Test Mode for nRF51422 on my board, I'm trying to use the nRFgo Studio.
When I'm trying to connect to the specific COM port, I get the following...
Custom Board which has NordicSemi nRF51822-QFAA MCU,
a temperature sensor (Si7020-A10), and a white LED. The circuit follows the internal LDO setup.
(Ref. nRF51822_PS...
Hello,
i use Bootloader from SDK 7.2.0. I have some questions about init packet handling:
The bootloader compare the device type, device revision and softdevices...
