I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi,
Sorry if these are silly questions but I've tried some searchings and still cannot figure out the answers for the questions below
What is GATT Server Context...
Hi,
I wrote some code that writes to the flash perfectly when BLE is not enabled but when it is enabled, some of the data are correct while others are either missing or...
Hello folks, I have modified the SPI Master Loop example from the package so that I could communicate with the ADXL 345 accelerometer. I use the "spi_master_send_recv()" function...
Hello,
I'm trying to retrieve data from a nrf51822-based board that supports the BLE NUS sevice (using the ble_nus Library provided for the uart communication example,...
Hello!
I've just started using the nRF51 dongles (currently having 5 of them) and I would like to test the GitHub mesh protocol . Excuse my lack of experience, but I am...
Hi,
I'm trying to load the ble_app_beacon application under C:\Nordic Semiconductor\nRF51822 Beacon v1.1.0\Source Code\nrf51_beacon\ble_app_beacon\pca20006\s110\arm_build...
Hi there,
Is there any way to resolve a BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE address without using whitelist advertising? If not, I guess I should implement the...
Hi,
As question "custom serial wire debug" date Jan 14 '14, I'm also interested in programming the chip from an other embedded chip (would fit our production process verry...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi All,
I am using the nrf_udp_client example project in IoT SDK as the code base for testing the UDP communication.
For network topology, the nrf51-DK plays the role...
Hi everyone:
I have some question about nrf51822 power on sleep mode
in example ble_app_hrs have a "power_manage" function and it will make the system go into power...
Hello all,
I have a simple C++ application flashed to my device to operate the UART - every time I send a char from an external source, the device appears to reset - specifically...
Hello
I was wondering if it is possible to run to separate LP-comparators on the PCA10001? I've taken a look at the example code for LP-comparator in the SDK, and i was...
I'm using interrupt_handler.c for a bootloader without a softdevice from this source . Interrupt handling in the main app seems to work fine. But interrupts in the bootloader...
Hi,
In the nrf51_bitfields.h file, I can see definitions for two registers POWER_RAMON and POWER_RAMONB.
But I don't see this RAMONB in th nRF51 reference manual and...
