Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi, all!
I am rencently studying ota,and that is what I have done:
Program softdevice 6.0 into my nrf51822 chip.
Program bootloader(version in SDK5.2) into my nrf51822...
hello everyone,
I recently purchased the new nRF51 dongle. I could successfully load the blinky example with S110 soft device to it. But it is not working with the HRS example...
Hi, I am trying to use your new sd 8.0.0 but there are a lot of compilation errors due to the new APIs and removed section from security structs in SDK 7.2.0.
Are we to sole...
Hello
I have the nRF51822EK PCA10001 (V1.0) and PCA10000 (V1.0).
I'm working on a project where i'm going to send data from a custom board over to the PCA10000 dongle...
Hi all,
I have a small question. If a GATT server needs to send data to a GATT client(about 65 bytes), does it have to create a service first and then adds characteristic...
i am trying to make connections between s130 device and end node which have heart rate service.
according to the s130 document once if you press the button 0 it will automatically...
Hi
during setup of a peripheral at startup, I need to add some wait periods in between steps of the setup. Is there some function like waitMS(int time) or something, that...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Folks,
Newbie here with mbed, using nRF51-DK, but old hand with nRF51822, S110, SDK, J-Link, Keil MDK, etc. Trying to figure out how the mbed SDK API maps down onto the...
I have 25Q64 SPI flash chip connected to SPI bus. Unfortunately it works too slow even with using IRQ routine via SPI0_TWI0_IRQHandler (everything done like in example spi_master...
I was wondering if its possible to do a "Create new user" function, so the new bonded devices are accepted only if the first connected master tells the peripheral to.
For...
Hello,
I have taken the ble_app_beacon example and added a few things... I am looking to do something very simple like light up an LED on connection. So i added the on_ble_evt...
When is the S130 going from alpha to beta or release?
I understand that what ever answer is subject to change...just hoping to get a "ball park" date/plan.
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hi,
I am using NRF51822 BLE. I wanted to know that when we put this BLE ic in sleep mode then, is there VDD_PA voltage is still 1.6V or it becomes shut off internally.??...
