Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
I am trying DFU to work with gcc and SoftDevice 7.1.
Problem :
MCP able to send the APP binary successfully to the bootloader and DFU bootloader correctly write the app...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi, guys. Now I check the nRF51 IoT SDK(6lowpan, ipv6 over bluetooth).
nRF51 IoT SDK is needed Raspberry Pi, so I make the VMware Player Image for
Ubuntu 14.04.1 LTS 64bit...
I have a nRF51-DK. I would like to control the nRF51-DK through my mobile device.
What is the max. distance which can be reach with BLE(nordic chip)?
Is it possible...
Our application uses the S120 stack, and a bootloader. We want the bootloader to be able to update both our application software and the S120 stack (preserving the MBR). ...
Hi folks,
I have been successful in getting sample code compiled using Keil u-vision and MBED and installing it on nrfDK-51. It has become so simple to install apps - all...
Hi everyone,
I successfully compiled and loaded the experimental_ble_app_uart onto my pca10028 board.
I downloaded and installed the nRF toolbox on my nexus 7 tablet....
Hello everybody,
I want to do something very simple: Read some data from my Bluetooth peripheral. I know the UUID of the data I want to read, but I do not know the handle...
Hmm... this should be a simple question. But I haven't found a direct answer yet in the online SDK docs, the ARM NVIC docs, nor in this forum (and have only been confused...
Hi All,
I have a following setup :
The peripheral BLE device is supposed to send **(time critical )**data packets to Central device but the transfer is very rare (Can...
Hi,
I have modified slightly the OTA bootloader sample in SDK6.1 and SoftDevice 7.1.0. After flashing the bootloader code to the nrf51822 it works like charm, I can update...
when i use BLE_GAP_ADV_TYPE_ADV_DIRECT_IND mode,I can see the device advertise (MCP) but i couldn't able to connect with it (advertising_start at BLE_GAP_EVT_TIMEOUT)
i...
Hi,
I'm a beginner with bluetooth.
I'm actually working with nrf 51822 Evaluation board.
I want to realize a transparent mode of communication with your kit. Can you...
I never worked with Cortex M0 before so I wonder how it's possible to jump to correct IRQ handler when I have my own bootloader and application which are using e.g. UART IRQ...
Hi.
Where i can find some information and guidelines to do a good RF PCB with nrf51822?
thank you for your support
EDIT 02/02/2015
Where i can find " nRF51822 Reference...
