Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hello,
I integrated the relevant code from the "uart" example into the "ble_app_uart" example(this is all the code in the main routine):
uint8_t cr;
uart_init();
...
Hi all:
I use sdk11.0
<nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay>
this example, scan heart sensor , sdk return...
It would be helpful to know how a packet looks like when transmitted/received from the NRF9E5 chip. I already found the algorithm to build the correct CRC, expected from the...
I have included the DFU service and a custom service in my application. During initialisation DFU service is getting initialised and later down the line my custom service...
Hello,
I have few question please about this example.
m_lesc_private_key looks unused, how to modify source to use a pre shared private key ?
is this exemple secured...
Hi!
We are trying a new module with NRF24l01+. We find a troublesome thing. On this video you can see the RF communication starts and stops with a broad-spectrum signal...
Hi :
In my application, i need to use 2 spi master (SPI0,SPI1) and spi slave the same time, but when i compiled drivers_nrf/hal/nrf_spi.h and drivers_nrf/hal/nrf_spis.h...
Hi. I'm using nRF528332, SDK13, S132.
I'm making multi-link peripheral refering to "experimental_ble_app_multiperipheral".
This example code says as below.
#define...
Hi Nordic,
In my application, I want to consume as less power as I can. In the initialization I have this functions:
static void utils_setup(void)
{
APP_TIMER_INIT...
why not provide the ready-made tools？ like micro_ecc_lib_nrf52.lib and nrfutil.
because it 's really take user a lot of time to built these tools.
thank you.
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hello ! I'm beginning work with BLE . I have a project in which nrf51 is a central. App from smartphone will sending to central any key for example "3214941E0" when central...
Hello Nordic community,
I have a question about implementing DFU on the custom board. By looking at NRF52 DK and reading explanation in Nordic infocenter, I can see that...
Hi,
I am have a custom breakout board that uses the NRF52832 chip and I was able to program it using the J-link programmer and seperating ribbon cable to expose the Vtarg...
How do I maximize range for BT5?
I have two nRF52840 pdk units and I have loaded the ble_app_att_mtu_throughput app and tried it out. I have been seeing around 70 meters...
