Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
We have an ISR parsing incoming serial data from the UART. When a valid packet arrives, I'd like to be able to wake the core from whatever low-power state is entered when...
That is probably an old topic, but after doing some research I could figure it out: calling sd_app_evt_wait() on my nRF5832 + nRF5 v11.0.0 SDK + s132 causes my chip to reset...
Hi
I've some troubles with the ble disconnection of S110.
Always when I call the sd_ble_gap_disconnect function after successful connected, the error code 8 NRF_ERROR_INVALID_STATE...
As I can see, I flashed Zephyr to Carbon 96 board, I don't fully understand the process,
I mean, I see .bin and .elf files but i don't see boot.img file, how do i make a...
The nRF52832 datasheet refers to a transmission of multiple packets in Figure 37. I have attempted to load multiple packets to the radio FIFO using nrf_esb_write_payload(...
Hi All,
I have developed an application on the RedBear BLE Nano2, and am trying to port it accross to a custom nRF52 board.
The Hex that the Arduino IDE outputs does...
I have an application which requires protection from passive eavesdropping, but not man in the middle attacks. I want to enforce the use of diffie hellman key exchange.
...
Hello
i am using Nrf52840 with sdk 132 and version 12.2
i am using the Heart Rate example as template.now i am just testing.
Before making connection,i like to Advertise...
I have a sensor which has output in the range of 0-5V. I want to connect it to an nrf51822 GPIO pin and to be able to read the value via it's 10 bit ADC. Is there any guide...
hello, there my application is like that...
(1) calculate size of receive buffer. than read that size of data.
again new data comes, then again calculate that size of...
Issue: With my external antenna design, I get lower dbm than PCB antenna (nRF51DK) with same distance.
My external antenna design: -70dbm
nRF51DK: -40dbm
In this...
Today when I started power profiler kit, it suddenly started to show peak values like 80 mA. This has not happened before, but the values with the same hardware have been...
In the data sheet of the NRF51 and 52 there is mention that sensitivity of NRF51 is -96 dBm and NRF52 -98.
But I read some where that when RSSI is -90 then that signal...
We are working on a dynamic radio power change for a proprietary RF protocol, and we are missing some granularity on the NRF_RADIO->POWER levels.
Typically we would need...
