Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I have used NRF52840 and SDK 13.0.0.
When I have used USB or ESB one by one - all is Ok.
But when they are used together - usb driver goes into an infinite loop here:
...
Hello.
I am developing a project on nRF52832 using SDK 13, in which I need to transfer up to 300 bytes of data from iOS device via my dedicated app (in the background) to...
Hi,
I read in the documentation that one can loop a complex playback. The way I understood, one could load a first sequence (say seq1) and a second sequence (say seq2)...
Hi Nordic Team,
i am working on nrg52 to glow a RGB LED with white and Yellow colours. configured the RGB pins to three different Gpio (A2,A3,A4).
for this i am using...
I have an application where I read a IMU at around 60 - 80 hertz.
How should I configure the S132 so I can send my 14 byte string packet with a constant time interval?...
Good evening (at least here...)
I successfully developed an application with Keil on the Rigado EVAL board with the following steps:
nRFgo Studio -> erase all and...
Hi,
is there a way to make a all in one bootloader image which includes Softdevice and APP in one zip?
And is there an example of the DFU via a Master uC. My setting is...
Hello all,
I am trying to program my custom board using the debug out from the nrf51-DK.
I connect all the needed pins and on the nrfgo select the Segger but when I do...
Hi,
I want know how nrf51822 bootloader finds images type(means weather it is softdevice,bootloader,app) when we pass an image to bootloader for update. And also how bootloader...
There is a list of 3rd party modules at www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules . Will it be updated to include nRF52840 modules?
It appears the nRF51822 Product Spec does not list the current nor power for the radio DISABLED state. The Reference manual description of the state is “No operations are...
Hi everyone,
First post here, so apologies in advance for lowly questions!
I have a Fanstel EV-BC832 dev kit for their BC832 module , which uses the 516K Flash / 64K...
Hi all,
Having a bit of an issue with the SPI manager scheduler. When sending small packets (<4 bytes), I seem to be able to queue as many requests as I want.
However...
I asked the following question, TWI Stuck Bus Recovery , last week and got a great answer which I implemented. I tested my implementation by changing the device addresses...
