after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am developing a project with NRF51822 and i want to block signals in one direction. Is it possible ? And if it is possible, how can i do this ?
Thanks !
(PLEASE SEE COMMENT BELOW)
I've got a Nordic project that I imported into Eclipse as a makefile project. I've got it working and I can debug into it. Everything is good....
OTA problem：
My hardware is 51822qfaa .
This my bootloader: nRF51_SDK_10.0.0_dc26b5e.rar
location: nRF51_SDK_10.0.0_dc26b5e\examples\dfu\bootloader\pca10028\dual_bank_ble_s110...
how many uart can I use at the same time in nrf52832
i know in nrf51822, every pin can use as uart,but at the same time ,i can only use one uart.and now ,i have a case...
Hi,
I have an issue with app_timer (nRF52, SDK13.0).
I use a single shot timer.
I try to debug, and I'm in the case of app_timer.c line 650:
ticks latest: 534879...
We need to connect at the same time
several mobile phones with the Android OS to a single device
nrf51822 via BT in our upcoming project.
According to information from...
Hey,
Just had a quick question... I was doing the Relay example and I don't totally understand what a "relay" is. Can you explain what the purpose and usage of relay is for...
Hi,
i am working on RTC to create custom clock to measure time it is working fine but when i initialise ble stack and softdevice and adverticeinit it is not working. and...
Hi,
Maybe someone can point me into the right direction, I'm on S110 and SDK10 for hardware/legacy reason.
I have a pstorage function using init, load, clear and write...
Hi.
I am investigating the cap touch for a while, and I am working directly with the capacitive driver from here.
As being said there and other places, the driver will...
Hi all
What is the minimum required length of a LOW pulse to be detected by the nRF52832 via GPIO SENSE mechanism? I couldn't find it in the product specification.
I...
Hi Nordic Team,
I am using board PCA10040 wtih nRF52832 SDK 11.
I have Added DFU code to ble_app_hrs_freertos example.
Once I will go for DFU from nrf Mobile Application...
Hi all
I was investigating a NMI_interrupt today and found out that it was caused by a race condition in the fstorage module.
The problem may occur after a flash operation...
