I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I have a board with a NRF52 (3rd party board), there is a 32MHz crystal with the correct load capacitors on, but the crystal is outputting 1MHz on a scope (Tektronix...
Hi,
I'd like to output some audio data through i2s. It's quite easy to understand your examples provided on infocenter, however, I can't get my code to work.
Here is...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I need to take data from sensor board through uart and send to mobile through ble for every 500ms. Sensor...
Hi guys
I want connect nrf51822 (Raytac MDBT40) by my phone(HTC battery one android 4.4.2).
I use softdevice 130(ver.2.0.0) and SDK 11 demo code under KEIL ARM 5.
...
when i run sudo nrfutil dfu serial -pkg my_package.zip -p/dev/ttyACM0 i get the following error:
pc_ble_driver_py.exceptions.NordicSemiException: Failed to send init packet...
Hi
I am working with mbed targetting for ReadbearLab Ble Nano. I am trying to encrypt payload before sendind it with:
include "nrf_ecb.h"
...
int main(void)
{
...
Hi, i'm using keil and i would like to run the fpu_fft example to perform a fft. The example works if I set 128 or 256 as number of input vector data as you can see in the...
I'm using SDK 6 + S110 v7.
Is it possible to use device manager to perform bonding but don't write bond information persistently in flash?
With old bond manager I could...
Could someone please guide me through the process?
I believe it can be done through nRF Studio which I have downloaded, but don't know how to proceed from there???
Tks...
Dears,
I am developing a ANCS application with nus service on our product. There are a few problems I don't know how to fix it.
My problem is that :
1. ANCS will not disconnect...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
I have request similar to this questions but for SDK13:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
Judging by quick grep sdk_config.h from ble_app_template...
