Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
hello,
my custom hardware includes 10 buttons connected to 10 GPIOs of a nRF52832. The nRF52 is placed in low power or eventually system OFF all the time, waiting for a...
hello i am using the nrf52840.
how i can set the 4Khz frequency in low_power_pwm.
low_power_pwm_config_t have period parameters. which value i need to assign to generate...
Hello,
I am trying to migrate to the latest S140 SoftDevice, but the migration document leaves a lot to be desired and is missing information. I've had issues running standard...
Hi
I'm migrating to SDK14 currently. My program seems to hit an infinite loop (or something of the sort) after I call my_service_on_connect() from my_service_on_ble_evt...
Hi all,
I have a custom board with a nRF51 and a DSP connected to eachother (SPI, UART and I2C) and since I have no connection to the nRF directly or any buttons I need...
I want to change the light-control example given in mesh SDK such that instead of using buttons to trigger messages, I want to connect client with mobile and control servers...
Hi, I am working with app_uart module and during the reception process sometimes there will be APP_UART_COMMUNICATION_ERROR event generated, my question is why there is such...
Hi,
I am testing with ble_app_uart code for handling UART data. If the data is more the device is getting disconnected from the central device. I am thinking that, BLE...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
I have the test that spi communication between nRF51 DK(Master) and nRF52 DK (Slave).
use the example projects in SDK 12.2.
success build and writing but i have got...
I would like to utilize six Sampo S1 readers (yes, I only read for now, I know they can do much more) to count people entering and leaving a conference.
I am looking for...
I implement it with sdk 11.0 and a third party board.Firstly,I program s132_nrf52_2.0.1 SoftDevice by nRFgo Studio，secondly，i program dfu_dual_bank_ble_s132_pca10036. then...
