Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
hello everyone:
i use nrf51822QFAC(with 256kb flash and 32kb ram).The project is this "SDK12.3-ANCS\examples\ble_peripheral\ble_app_ancs_c\pca10028\s130\arm5_no_packs"...
Hi all,
I have a board with old code, it has a bootloader + sofdevice 110 + application all from SDK7 and I want to upgrade it via serial single bank DFU, to the SDK11...
I've developed a PCB containing the nRF51822. I am trying to uploaded the example program "ble_app_uart_s110_pca10028" to it, but the chip is not broadcasting (so I assume...
I use buttonless_dfu app from sdk 14
Generate settings file by nrfutil
Merge with bootloader hex file
Erase chip, flash SD, flash bootloader (everything use nrfutil...
Hi,
I am using SDK 12.2.0 with secure DFU service.i want to use pwm in my code.And i init pwm with APP_PWM_INSTANCE(PWM1,1),then i get an error:identifier "TIMER0_ENABLED...
I have built a custom board that is identical in schematic to the nRF52 DK board, with some additional circuitry connected as a SPI interface to the nRF chip. The MCU is the...
Hi,
Glad to see Nordic just released a new alpha version SDK yesterday!
I am wondering when you will release the mesh friend nodes support SDK? I mean support those low...
Hi,
I need you suggestion / information about Nordic chip. We currently have nRF52 (nRF52832) chip. However, in our application we will be using Nordic beacons as an transmitter...
Hello All,
I've finally managed to get Eclipse up and running after migrating from Keil, but now I'm having the following problem: I'm trying to port the buttonless_dfu...
Hi,
Happy Monday! We have multiple PTXs and multiple PRXs in a setting, all operating on a single channel. Is there a way to allow a PRX to receive but disable it from...
Hello,
We have observed fluctuation in Gas sensor readings from Nordic Thingy:52.
eCo2 and VOC readings are not at all near the calibrated sensor readings.
Tried Nordic...
Hello,
I am in a little bit of trouble here trying to flash a 3rd party module that is mounted on a custom PCB I made with the SWD pins exposed for programming.
I've...
Hello,
I am using pca10040 and sdk12.2. I am using nrf_beacon code. I flashed the code in dk. I am able to scan the beacon but I n/a appears as default name in nrf connect...
Hi team,
My 52832 act as central device. It can discover service and characteristic of peripheral. The problem is it can't get the UUID of every characteristic of service...
