hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Can't I connect to device that hasn't been discovered yet??
I'm trying to connect one device( A ) to another device( B ) which ADDRESS is known but never discovered yet...
Hi there,
We're looking at doing something with beacons so that we can make use of the way iOS handles scans for them in the background differently to other peripherals...
The debugger does not work with the latest GNU toolchain for ARM Cortex-M build. It throws the following error on Eclipse:
Could not determine GDB version after sending...
GPIOTE Library makes my Board(nRF51422-QFAC) Brick??
I just build my nRF51422 Board, and It's pretty working well before I've used GPIOTE Library.
Before using GPIOTE...
Hi everyone,
I am seeing an issue where the SPI (master) ignores the first byte of RX buff and begins storing the received bytes from RxBuff[1] instead of RxBuff[0]. In...
Does anyone know if there is any documentation of nrf51822's current consumption? Perhaps, something similar to CC254x's Application Note . I'm mostly interested in the current...
Hello,
I would like to build two boards that can send small messages between them, at long distance. For that I would like to use some of your devices (I used 51822 in...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
Hi Engineers!
We made our own ten (10) PCB's with nRF52840 MCU onboard fully according to "Circuit configuration no. 3":
1. LDO only mode (VDDH connected to VDD connected...
I have a custom circuit with nrf52832 which I am trying to program.
All i/o pins seem to be working fine except pins P0.06 - P0.10.
I'm testing it with mbed (digitalout...
Hi,
Thanks for taking the time looking into issue.
We are using Keil uVision 5.14.
Our target is a custom board (BMD200 eval Module based on nRF51822)
We were able to...
Hei guys,
for a new custom board based on nrf52832 where i have to minimize power:
have an external Li-Po battery, with a cutoff @3.0v, so the range will be 4.2v...
blesc_pairing_dhkey_check_failed.zip
Hello,
I used the example ble_app_multirole_lesc and paired with nRF Connect app. However I got the error message (in Bluetooth...
Hi!
So I have my GATT value of a service that I would like to update.
Sadly that value always stays at the initial value.
Below you can find my update function.
uint32_t...
