Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hello,
I am using the Nordic NRF 51822 chip and are am wondering if full Eddystone support can be found in the latest firmware? I have read on github ( github.com/.../nrf5...
Hi,i m working in uav project with nr52 and GY-87 that contains mpu6050 and hmc8553 as sensor. i use i2clib to do connexion with twi created by jeff rowberg, then i wrote...
Hi,
I'm trying to add Openthread support to my project, which is based on ATT_MTU_Throughput example. I followed the tutorial in infocenter, but I still have some problems...
Hi,
I am attempting to run the various USB example programs on the nRF52840-PDK USB, but my nRF usb device is not being recognized (in windows OR linux device tree). Is...
Hi.
I just spend 2 days debugging problem with dfu. In the function nrf_dfu_app_continue the function nrf_dfu_flash_store is called with len parmeter as bytes and should...
Hi, I would like to control 2 LEDs independantly with the same server node. Should I try to [1] add a element with the same simple on/off model in that server node OR [2]...
Hi,
I'm running an ADC sampling every 8msec, sampling the output value of an op-amp as well as a reference voltage. I subtract the two in firmware. I was implementing the...
Hello,
I am using SPI interface to communicate with a sensor BMI160, looking into the driver for BMI160 I can see how the low level functions for reading/writting are used...
Hi,
i am trying to upload the code to BLE 400 from waveshare from nrfGo by getting the hex file from this library
While Trying to upload the code i am getting the following...
onkey_full_20170814.hex
onkey_0000.hex
onkey_boot_s132.hex
This time 14.0 sdk was updated.
There was a problem after the update
Problems when uploading bootloader...
Hi,
I am using SDK v12.2 and gcc compiler. S132 softdevice for nrf51 controller.
I am using muliple nrf51 devices to connect each other and share sensor data with each...
I'm using a pin for trigger switch input with the following codes
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;...
Hi,
I would like send serial data in both directions (like by RS-232) between BMD-300 Evaluation Kit and BLED112 dongle.
I'm a beginner on this subject, so I'll ask...
