I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi all, I'm working on sdk11.0.0 signed bootloader and I made change in it. Due to these changes bootloader size increased and not fit in the memory allocated to the bootloader...
Hello:
The product specification (v1.3, pg 263) says temperature sensor accuracy min = -5 C and max = +5 C.
Its not clear if these accuracy values correspond to the...
Hello,
I meet the same problem with the question " Status bit for sd_flash_write() ".I have register my flash_nrf52_sys_event_handler() in sys_evt_dispatch(),but after...
I am trying to find examples for nRF51 dongle P10031. I would appreciate some guidance and help regarding the same. Its my first time using the device.A link to a sample example...
I have this working and producing good and accurate results, but I'm still puzzled by some of the examples in the SDK and the documentation.
I am using the processor to...
Hi,
In my application, using BMD301 i have made one custom PCB. I am using SDK 12.0.0. In my PCB I have not used all the four LEDs. I have assigned p0.19 to the BSP_LED_0...
I'm using SDK 12.2, and nRF Connect on a Windows machine. I started with the ble_uart example.
I need to send data in my advertising packets. In advertising_init() I initialize...
This is referring to running a peripheral device on the PCA10028 eval board.
Let's say I have a connection interval of 100 ms, and a slave latency of 5.
So the BT stack...
Hello, I am using an nrf51822 but have no success in advertising.
I tried so far to load the ble_app_template from the peripheral examples where I' ve only changed
#define...
Hi,
I am looking for a BT module that can connect to both a BT Jabra audio headphones in addition to a BT HR chest strap with 2 live connections simultaneous.
Do I have...
I understand part of ram is used by the softdevice, but I see different addresses are used in different examples that use the same softdevice, namely S132. For example,
...
I am trying to run the examples given by Nordic on my nRF51 dongle. Most the examples are for PCA10028 or PCA10040 where as my dongle is PCA10031. I tried running them but...
Hi,
I need 6 PWM channels for a BLE project. Is there any solution to add 2 other pwm channels to nRF51822? If not, Which other Nordic ICs might be helpful instead?
Thank...
