I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
hi,
i need to do long process and more flow of functionality that all could stopped by softdevice. so i need to enable and disable soft device. could it could affect my timer2...
hi
here i have use block size 16 byte and block count 5096. this is my start address 0x27000
i have tried to clear 79 pages.
and read data from flash with specific...
Hello to all
I have the next code, basically what it does is reading a button state and if it is pressed then the manufacturer data of the BLE package is lets say B, on...
Hi All,
I would like to know what the default value is for the radio TX power for the nRF5240. According to Nordic's specification, the output power is programmable from...
In the ULP Wireless Q magazine (edition winter 2016), on page 12 / 13 there is listed that the nRF52 chips have a Battery Monitor peripheral but I cannot find anything about...
I have been developing my application using gcc on an NRF52 by putting the text section at 0. This was convenient to get going quickly. We initially weren't going to launch...
hello, i am doing flash read and write in nrf51.for which i have used the C:\nRF5_SDK_12.2.0_f012efa\examples\peripheral\flashwrite\pca10028\blank\arm4 this exampl.
but while...
Hi,
Could somebody share the schematic and board files of nrf51 beacon?
We are planning to make some changes. I don't intend to buy a beacon because I have already purchased...
Hi,
I use the bootloader in the SDK V13.0, I found that no timeout as the SDK v12.x. However, I have added the WDT to the bootloader refer to the link link text
it still...
i could not run timer2 with soft device,. if i start initiaize TIMER2 the bluetooth advertise has disabled. i need this timer to timeout my flow function. i think softdevice...
Hi,
I used the hrs example found some problems, the problem is described as follows:
I use the Android phone pairing binding device, when I cancel the pairing on the phone...
hello,
What is the difference between the next two events?
On_ble_evt ()
BLE_GAP_EVT_TIMEOUT == 0x1 B
On_adv_evt ()
BLE_ADV_EVT_IDLE
I can not understand well.
With...
Hi;
I do not know the BLE Event(DFU bootLoader/SDK Sample) so I will ask you a question.
The environment using is below.
SDK v10.0.0 (Sample code/dfu_transport_ble...
