This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
I have merged all the 4 file's together (app.hex, app_valid_settings.hex, softdevice.hex and dfu.hex).
Then I uploaded the custom app with dfu services enabled using nrfgo...
Hi there,
I'm porting an app from NRF51 SD130 to NRF52 SD132, both with sdk11. I do the usual stuff, like changing includes, freertos ports libraries, etc, and everything...
Just a general resource question. The Softdevice uses RTC0, FreeRTOS (by coded default) uses RTC1. So in order for the SDK ble_conn_params.c to run properly I have to link...
I was able to add the Device Information service as well as a proprietary service using a 128 bit UUID. I modeled after the ble_peripheral uart example. However when I try...
Nrf52/Kiel/SDK11
My application was at the point where I needed to add DFU. Following the examples and SDK doc, I added the files and code needed. It would NOT advertise...
We recently moved from SDK11 to SDK13. We run out of memory when adding custom services & chars to the S132 v4.0 softdevice. Increasing the app start address in the linker...
For the record I have been struggling with migrating a project from S110 @ nrf51422 to S140 @ nrf52840.
Quite by accident, I found this "nrf51_to_nrf52840.h", what does...
Hi , Everyone!
Now i have the board nrf52832 and i'm conducting my DFU.
My DFU is to update softdevice and application.
Here is detail about my problem:
softdevice...
Hi
From s140_nrf52840_5.0.0-3.alpha_migration-document, it is mentioned that the L2CAP API has been completely removed. Are there plans to re-expose the API? We have exposed...
I'd like to clock the nRF52840 at the same frequency as my converters. Is there any problem with using a somewhat different frequency than the 64 MHz (or 32mhZ) crystal? If...
Hello guys,
i randomly get twi error busy 17.
i have #define TWI_DEFAULT_CONFIG_IRQ_PRIORITY 7 in sdk_config.h and .interrupt_priority = APP_IRQ_PRIORITY_LOW in init function...
My setup is based on a jlink clone and yunjia module nrf51822 and nRF51_SDK_10.0.0_dc26b5e. I am following this tutorial successfully till the section Enable auto discovery...
Hi,
The following function/macro is missing in SDK 12.2.0 and 12.3.0 but existed in 12.1.0:
nrf_drv_saadc_gpio_to_ain
I am re-compiling "thingy" SDK and it happens...
I'm looking for an answer as to how to know the source files that I need to mention in the Makefile if I'm writing my program from scratch. Are there some bare essentials...
