Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Need help from the mesh experts in this forum!
I'm running the open mesh in the 52832 with the s132_nrf52_3.0.0_softdevice.hex softdevice. The mesh works fine in my tiny...
Hi,
I connected 74CH595 shift registers to nRF52DK board. When I built and upload my code with Keil everything works just fine, but if I compliled it with GCC and upload...
I want my device not to disconnected.
I'm trying with custom board with NRF51822AA.
I customized NUS example a little.
And also I've downloaded NUS example for Android...
I'm writing a firmware, with SD130, using mbed libraries.
Firmware used to run fine. I added a new object, and now, when connecting, it hardfaults.
I put a breakpoint...
Hi everyone on the community.
I've been struggling trying to upload the hex file created by arduino using redbear nrf arduino fork on a NRF51822 -v2 board that is being...
Hello,
last week I was trying to integrate a wake-on-motion-functionality for my hardware using some interrupt-handling. While that problem is solved, I came across some...
Hello,
I would like to stream sensor data from the Bosch IMU sensor over BLE at a maximum rate. I can collect data over I2C from the sensor but would like to know if there...
Hello to all nordic jedi masters out there!
I am using nRF SDK v11.0 with the nRF52832.
I am a little bit confused about the usage/meaning of the flag argument in the...
Hi all,
I am trying to send a large stream of bytes(60kb) to an NRF52823 using bbowl . BBowl exposes the uart through a TCP socket connection using noble .
I modified...
Hi,
In the schematic presented in the topic 17.1 (dc/dc converter, image below) of the nRF8001 datasheet it isn't shown that AVDD should be connect to a power supply as...
devzone.nordicsemi.com/.../
In this blog this is written:
"Opening and closing a connection event adds a lot of overhead"
how much is the overhead and where can i...
Hello,
I am currently developing a new bt-le-program and besides my own log-messages, I wanted to enable also the log-output that is happing in the files from the Nordic...
I'm building something based on ble_app_gls. However, I only want it to be pairable when I say so (user presses a button to put it into that mode). Is there a "correct" way...
Hi,
upon connection I get these messages via RTT:
nrf_ble_gatt:DEBUG:Peer on connection 0x0 requested an ATT MTU of 185 bytes.
nrf_ble_gatt:DEBUG:Updating ATT MTU to...
I would like to know how to dampen the effect of metal surface on BLE signal . Let me give you an instance, i am installing a wireless sensor inside a metal box and this sensor...
