Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
I've run an mesh example of light control with three 52832DK board.There are some question.
[1]Now i want to add uart function to the example,then i can send msg without...
Hi,
I'm working on modification of DFU Bootloader to use external flash instead of standard Dual-bank or Single-bank version. Now it works quite well, but I have problems...
For programming the nrf52832's BLE capabilities the only option that can be used is the s132 soft device right?
According to the latest specification, the maximum throughput...
Greetings,
I have an application where the DFU of a NRF52 is performed by another microcontroller via a serial port. Once the DFU is complete, the microcontroller turns...
Hi everyone!
I'm wondering about why SoftDevice stays idle (in terms of radio operation) so "long"
("t ScanReserved" = 760 us) after channel changes during scanning? Despite...
Hi,
I'm trying to do a rough calculation of current consumption for the nRF52840 chip.
The unit should sample 6 times an hour by using I2C to acquire samples from a...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
Hi,
We are designed our own Beacon PCB based on nRF51822 Beacon Kit...We followed board size,PCB Antenna Trace width and GND Clearance as per Beacon kit...The difference...
As I understand it only the largest physical chip, 7x7mm nrf52840 , supports Bluetooth 5.0 long range. Is this correct?
It seems as if Nordic Semiconductor is abandoning...
Hi,
i have assigned RAM address as:
#define RAM_MEMORY_TEST_ADDRESS (0x20002BD8)
uint8_t * p_ram_test = (uint8_t *)RAM_MEMORY_TEST_ADDRESS;
to this p_ram_test i...
Hi,
In the Thread API under the Command Line Interface section, there are the following functions:
void otCliConsoleInit(otInstance *aInstance, otCliConsoleOutputCallback...
Makefile (/attachment/ca6852bdad7b5e54aaa4ce4388c4c410)Please find my code attached!!!
I have changed the makefile and the SDK config file accordingly! but the error remains...
Why can not read twi data ? at nrf52832 chip....
but Read well in Arduino....
twi interfacing with RTC DS1307....
please give me some hint.....
nrf_drv_config...
i would like to print register values of an external sensor on my screen using UART! I'm reading and writing into those registers using SPI! Printing a normal message using...
