Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
now I used sample code of radio
change NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_2Mbit << RADIO_MODE_MODE_Pos)；
In transmitter code , I change
while (true...
Story Short: When trying to run the ble_app_uart example on a custom board with a nRF51822QFAAH0 chip, the code faults and resets at the point in tries to call sd_softdevice_enable...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
Using:
nRF51822
GCC 4.8.4
Nordic Sdk 5.2.0
and even Ole Morten's nice pure-gcc setup
newlib-nano and -flto
Within the startup_nrf51.s I found something...
The server has no I/O, so no way to press a button.
Can an attribute cause the BLE to set a bit in Flash, so at the next power up, it will read that bit and know to execute...
Hello,
I followed the instructions of KEIL in www.keil.com/.../ulink2_trace_itm_viewer.htm
However, I cant get any outputs in Keil Debug(Printf) Viewer using printf...
I purchased a bunch of ptr8000 boards off ebay from china to do some testing of the nrf905 without realizing they were setup for 433mhz, and I need 915mhz. Looking at the...
Hi,
I am currently testing a DAC with I2S input supplied by the nRF52832.
But unfortunately no signal is coming out from the DAC, furthermore when reading the error registers...
I'm looking to use the nrf open mesh on battery powered devices based on nrf51822. I would like to enable the mesh for short periods of time to transmit values (~50 nodes...
Hi,
I've just got the example running with one DK as ble peripheral and ESB at the same time uing the timeslot API and one DK as only ESB receiver.
I can communicate fine...
I have used following sources for my application:
profile:
-BleManager,
-BleManagerCallbacks,
-BleProfileService
uart:
-UARTService
-UARTManager,
-UARTManagerCallbacks...
Hi,
I've just started to implement the example
github.com/.../nrf51-ble-micro-esb-uart
for the nrf52. And it is now running so I can send and receive stuff via BLE...
