Im trying to use the https://github.com/apache/mynewt-mcumgr-cli project to update my rfF54L15 with a DFU package
Setup: Raspberry PI 4 and and nrF52840 USB Dongle
I...
1. I am trying to implement DFU(with USB&BLE) and USB Mass Storage with FAT FS filesystems on external QSPI flash. I am getting the following build errors- with SDK version...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Dear Nordic
I am programming with nrf52833,ncs v2.9.0 base on sample\peripheral_hid_keyboards
Peripheral side(nrf 52833) adverting as Scanner_CE42,and iphone connect to...
I have read info somewhere which said there is method to crack the protection just by setting UICR APPPROTECT register.
I want to know if Nordic has upgraded the protection...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
Hello,
We are developing nRF5340 SoC and is currently using Thingy53 as our reference design, our NCS version is v3.0.2.
So far, we've been able to use dfu-util tool to...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
What does error code 4 mean?
I am looking through the documentation for the error code number to string translation.
Why is starting a timer causing the error code 4?...
I am trying to sample the ADC every 2ms. I notice lots of slowness with BLE advertising and typically can't connect to device over BLE when sampling. I am using PPI, configuring...
Hi
I'm trying to run the HRM_RX exemple on the nordic NRF51422. This is my configuration:
-Eclipse IDE
-ARM GCC 4.8.3
-NRF51422_AAC0 so I'm using the lasest SDK 4...
hello,
i am trying to use the example for the ble_lbs from github.
I get no erros on compile and flashing.
But wenn i try to see the device in the master control panel...
I've been slowly and incrementally adding changes to the ble_app_multilink_central example from nRF51-SDK-6.0.0. This is an exercise to understand where my other app stopped...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello everyone!
Firs of all consider I'm very new in micro controllers programming/debugging, so your patience would be much appreciated.
I have a nRF51822 mKit like...
I use multilink_central example and try get information about discivered service:
APPL_LOG("[CLIENT_LOG]: Count of services: %d\r\n", p_client->srv_db.srv_count);
APPL_LOG...
my led connect whit a pin like this:
the led positive connect whit VCC and the negative connect whit a pin through a resistors.
when I config the pin as a output like...
using the nrfGoStudio to program s110_nrf51822_6.0.0_softdevice.hex
Tools:
Jlink,SWD mode as the figure:
but there are some problem
1:we can download demo BlinkLed...
Hi,
I need a RTC calendar ble stack on nrf51822 .
(turn on the RTC0 on ble stack and get the count, how to setting the rtc wakeup )
which calendar need follow :
track...
