Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi there~~ I'm trying to create a voice streaming application with the Mesh and the Nordic Thingy:52 I downloaded both the nRF5 SDK 14.2 & Mesk v1.0 to test the Mesh's light_switch...
Hi everyone,
Currently, my team is developing a BLE keyboard which uses 6KRO protocol. Are there any examples for the 6KRO protocol using nRF52 chips?
Thanks!
Update:
Hi again to everyone!
After a while, I've received a new custom board and a new cable to connect through P19. But everything are not working again.
Now, in...
I have a 12 MHz voltage controlled oscillator driving the nRF9E5 at pin xc1 and xc2 is open will this pose a problem for running the nRF9E5? The clock has a +-50ppm stability...
I am working on a project that requires me to wirelessly communicate with and program a left hand Oculus Touch controller, since dismantling it will cause damage. The controller...
I see I have more than 100 free pages (~ 101 KB) on Nrf51822 with SD130 but how can I assign all of them to the FDS module. I am going to manage a database with FDS on the...
Hello,
I am trying to use PCA10000 dongle with the pb-ble-driver-py libraries with absolutely no success, as I get a "Failed to open. Error code: 13" error.
I am running...
Hi, please!
The question is related to "nRF24L01P_Product_Specification_1_0.pdf" datasheet in " www.nordicsemi.com/.../nRF24L01P_Product_Specification_1_0.pdf" and to NRF24L01P...
Hello. Engineers.
I'm a beginner in nRF52832, I'm looking for someone who can help me.
I have nRF52832 development kit. I tried examples blankly with SDK14.0.
It working...
Hi,
I've recently come across a problem where in some cases my device's memory gets trashed.
Ideally I'd be able to set a watchpoint on a memory location so that I could...
main.c
I am working in sdk14.1 nrf52832 ble_app_uart_pca10040_s132 and ble_app_uart_c_pca10040_s132.
ble_app_uart_pca10040_s132:
nrf_ble_gatt_att_mtu_periph_set(&m_gatt...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
We are developing a test jig that also programs the Nordic nRF51822 on our board.
We are receiving the following error message from the command line programmer:
NRFJPROG...
DSP is Digital signal processing，But I first came into contact with the word，I don't know what is DSP？
Do you have any relevant documents to explain the words？
The second...
