Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hi, and thanks for reading this, I'm currently able to power the PCA10005 by sending 3.3v to pin1 of p2, and pin5 of p2 to ground, with this setup I'm able to program the...
HI,I am using 51822 to realize a double-direction uart link with a ble client and a server chip.Now the double-direction link is established and each side can receive packet...
in the sdk for the nrf51822 eval board there is source for beacon app in s110. I also purchased the beacon keyfab which allowed me to get the beacon app for android source...
Hi，
I'll develop a adevice, using nRF51822; And I also have some device used nRF2401A, I want to know nRF51822 can communicate with nRF2401A, or not. I know nRF51822 is compatible...
Hello,
In our development environment we use a lot of PCA10001 boards for various prototypes.
As a cheaper alternative would it be possible to use PCA10024?
I have...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
I'm running out of RAM in my 51822 app and I need to take a look at what's using RW and ZI memory. Very little memory is being allocated with malloc. The rest is allocated...
I am attempting run the rf test from the bootloader. But I have the following problems.
When I try to compile the dtm rf test into the bootloader I run out of space.
...
Hello,
I am using the nRF51822 Development Kit and nRFgo Studio Version 1.17.03211.
I have compiled the blink_example and the s110 ble_app_hrs in the nRF51_SDK_v6.0...
Hello,
I'm starting a new project based on nRF51822 and I'd like to configurate the bluetooth to be appeared and allows the communication managment ( I want to creat two...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi All,
A simple one,, I just downloaded the master control panel app for android in android 4.4 phone.
My question is how to do bonding and how to delete bonding info...
Hi All,
I am testing the functionality of NRF24L01+ and for my purposes I have configured it as PTX, No Auto ACK.
I am able to communicate with the chip just fine and...
