Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
nrf52832 code always block at nrf_spi_event_check, my application include a app timer 200s period, after timeout, drive spi to get a RF sensor for sending some data, and also...
I am working with the nRF52832, SDK14.0.0. I want to perform a flash write on a watchdog reset to save the current state. However, the watchdog resets after two cycles of...
I've used the 'secure_bootloader' project, updated with the public key, to flash on the DK. The project 'ble_app_buttonless_dfu' built and packaged as zip can be DFU'd with...
Is it possible to _send_ multiple packets per connection interval, using the pc_ble_driver (and a nRF52 or nRF51 DK) in BLE CENTRAL role?
I found some answers on the devzone...
Hi, I developed a static library including drivers for spi, twi, gpio, adc and few others. Now when I create application and link my library it works ok as long as I am using...
Hoping to get some help. Using swift3 and xcode 9.3.
I can write data from iPhone back to nrf52 peripheral fine if it is a Dbl.
When I try to write a UInt16, it crashes...
I plan on using the nRF51 Dongle meandered antenna for a design involving the nRF52810. Since the nRF52810 has an internal balun, does that mean that L1, L2, C5, C4, L3 and...
hi,
i have a custom board with nrf52832 as it's core. i want to program with st-link v2 programmer.
i am using sdk 14.2 and soft device s132 v5.0. on target location we...
Hi guys,
We have tested the mesh range in the nRF52840 chip (max tx power) in LOS and we got more than 200m.
W're planning to use the mesh network inside hangar with a...
I am still newbie in nRF52 dk . For my project , i am trying to send data from my sensor to the mobile phone through BLE App UART. Therefore first I have flash nRf52 with...
Hallo guys,
i tried some hours to receive the microphone and some other data from the Thingy 52 on an nrf52840 evaluation board and write it to an SD-Card.
Everything...
Chapter 43 of the OPS document for the nRF52840 says that the I2S interface has a "Low-jitter Master Clock generator" but I don't see a jitter spec for it.
What is the MCLK...
