RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Hello,
I follow the tutorial devzone.nordicsemi.com/.../
And in the step of copy examples
I only got ble_app_uart_s130_pca10028
and no package of s110 was found
I'm...
Per my another question:
devzone.nordicsemi.com/.../
I have taken the kind advice of Bjørn Spockeli but to no avail.
I tried this solution to enter debug mode:
...
I want to use the sd_ble_gatts_hvx() to send the notification with a packet, and the length of packet is 12 bytes, but the return value is "0x000C". I tested the length and...
Hi,
I try to run a dual mode(peripheral/central) with S130. I'm using SPI serialization and sending command form an external MCU. I try to follow the example ble_app_hrs_rscs_relay...
Hii all,
I am trying to work with dfu, I developing an application that works with dfu, when I flash the softdevice and bootloader the device advertising as dfutarg and then...
I've loaded the S210_nRF51422_5.0.0 softdevice on my board from the nRFgoStudio.
I compiled the ant_hrm_tx_auto_s210_pca10028 project with no problem. However, when I try...
Hello,
I am developing two systems. One is a peripheral that advertises both a beacon and a ble peripheral custom service (using nRF51822 with s110 softdevice). The second...
Hi,
I am trying to use an nrf51822 with a sensor that outputs value between 0-5V. What I am confused about is how to read input voltage on the beacon. I saw some people...
Hi,
I need to debug my perpheral device, but as I know if I do debug when SD is running, it can cuase the time sync issue, then cause the hard-fault. I know there's a way...
hi ken：
I use Nrf52832(S132) to act as central and peripheral at the same time, which like the project ...\nRF52_SDK_0.9.0_0c82e3e\examples\ble_central_and_peripheral\experimental...
Hi,
I run ADC mudule together with SD, but go into hardfault eatch when I release the HF-clock.
Chip: 51822
SDK : 10.0-alpha
IDE : Keil-472
I use this function...
Hi!
I have inherited a large codebase that I'm trying to migrate to SDKv10 from SDKv6.
The project also uses an A4960 BLDC motor controller. To bring the motor up to...
Hello,
Is my ram reservation right for nRF52 with S132 ?
see in app_ram_base.h APP_RAM_BASE_CENTRAL_LINKS_3_PERIPH_LINKS_1_SEC_COUNT_3_MID_BW = 0x2F50
RAM (rwx) ...
Hey,
I have been trying to create a notification characteristic for nrf51822. Whenever I add char_md.char_props.notify = 1; lightblue doesn't connect to it.
I do get a...
